2GR-FKS (LUBRICATION): OIL PUMP: REMOVAL; 2021 - 2022 MY Camry [10/2020

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during oil pump removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

*1: When the ECM is replaced with a new one, reset memory is unnecessary.

Battery terminal is disconnected/reconnected

Perform steering sensor zero point calibration

Lane Tracing Assist System

Pre-collision System

Memorize steering angle neutral point

Parking Assist Monitor System

Panoramic view monitor system

Replacement of ECM

Vehicle Identification Number (VIN) registration

MIL comes on

ECU communication ID registration (Immobiliser system)

Engine start function

Replacement of throttle body with motor assembly
Cleaning the deposits from the throttle body with motor assembly
Replacement of fuel injector assembly (for port injection)
Replacement of fuel injector assembly (for direct injection)
Replacement of fuel pump assembly (for high pressure side)
Replacement of ignition coil assembly
Air leaks from intake system
Gas leak from exhaust system is repaired
Replacement of knock control sensor

Inspection After Repair

Poor idle, etc.
Engine start function, etc.

Replacement of automatic transaxle assembly

Reset memory
Input transaxle compensation code into ECM
Perform road test to allow ECM to learn

Large shift shock
Deterioration of fuel efficiency

for Initialization

for Registration

Replacement of ECM

(If possible, read the transaxle compensation code from the previous ECM)

Reset memory*1
Transfer transaxle compensation code
Perform road test to allow ECM to learn

Replacement of ECM

(If impossible, read the transaxle compensation code from the previous ECM)

Reset memory*1
Reset transaxle compensation code
Perform road test to allow ECM to learn

Replacement of ECM

Code registration

Wireless door lock control system
Smart key system (for Entry Function)
Smart key system (for Start Function)
Steering lock function

Replacement of automatic transaxle fluid

ATF thermal degradation estimate reset

The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly.

Suspension, tires, etc.

(The vehicle height changes because of suspension or tire replacement)

Rear television camera assembly optical axis (Back camera position setting)

Parking assist monitor system

for Initialization

for Calibration

Replacement of front bumper assembly

Front television camera view adjustment

Panoramic view monitor system

for Initialization

for Calibration

Suspension, tires, etc.

(The vehicle height changes because of suspension or tire replacement)

Television camera controller initialization
Adjust steering angle
Rear television camera assembly optical axis (Back camera position setting)

Front wheel alignment adjustment

Perform "Reset Memory"
Perform acceleration sensor zero point calibration and system information memorization

VSC disabled or malfunctioning
DTCs are output
Slip indicator light illuminated
ABS warning light illuminated

PROCEDURE

1. REMOVE OIL PAN SUB-ASSEMBLY

Click here

2021 - 2022 MY Camry [10/2020 - 08/2022]; 2GR-FKS (ENGINE MECHANICAL): CYLINDER HEAD GASKET: REMOVAL

2. REMOVE TIMING CHAIN CASE OIL SEAL

Click here

2021 - 2022 MY Camry [10/2020 - 08/2022]; 2GR-FKS (ENGINE MECHANICAL): FRONT CRANKSHAFT OIL SEAL: REMOVAL+

3. REMOVE TIMING CHAIN COVER ASSEMBLY

(a) w/ Stud Bolt:

(1) Remove the 23 bolts and 2 nuts shown in the illustration.

Nut

(b) w/o Stud Bolt:

(1) Remove the 25 bolts shown in the illustration.

(c) Remove the timing chain cover assembly by prying between the timing chain cover assembly and cylinder head sub-assembly or cylinder block sub-assembly with a screwdriver with its tip wrapped with protective tape.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head sub-assembly, cylinder block sub-assembly and timing chain cover assembly.

*a	Protective Tape

(d) Remove the oil pump gasket from the cylinder block sub-assembly.