| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM100000001T516 |
| Model Year Start: 2021 | Model: Camry | Prod Date Range: [10/2020 - 08/2022] |
| Title: SUPPLEMENTAL RESTRAINT SYSTEMS: REAR AIRBAG SENSOR: REMOVAL; 2021 - 2022 MY Camry [10/2020 - 08/2022] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during side No. 2 airbag sensor removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
Disconnect cable from negative battery terminal |
Perform steering sensor zero point calibration |
Lane tracing assist system |
|
|
Pre-collision system |
|||
|
Memorize steering angle neutral point |
Parking assist monitor system |
|
|
|
Panoramic view monitor system |
|
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. PRECAUTION
CAUTION:
Be sure to read Precaution thoroughly before servicing.
Click here
![2021 - 2022 MY Camry [10/2020 - 08/2022]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: PRECAUTION](/t3Portal/stylegraphics/info.gif)
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here
2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
for A25A-FKS: Click here
for 2GR-FKS: Click here
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here
3. REMOVE REAR SEAT CUSHION ASSEMBLY
for Fold Down Seat Type: Click here
for Fixed Seat Type: Click here
4. REMOVE REAR SEAT CUSHION LOCK HOOK
for Fold Down Seat Type: Click here
for Fixed Seat Type: Click here
5. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP (for Fold Down Seat Type)
HINT:
Disconnect the rear door opening trim weatherstrip to the extent that allows the removal of the rear side seatback assembly.
6. REMOVE REAR SIDE SEATBACK ASSEMBLY (for Fold Down Seat Type)
Click here
7. REMOVE REAR SEATBACK ASSEMBLY (for Fixed Seat Type)
Click here
8. REMOVE SIDE NO. 2 AIRBAG SENSOR
(a) Check that the ignition switch is off.
(b) Check that the cable is disconnected from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
(c) Disconnect the connector from the side No. 2 airbag sensor.
NOTICE:
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
(1) Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)
|
*a |
White Housing Lock |
*b |
Yellow CPA |
|
Push in this Direction |
|
Slide in this Direction |
(2) Push down the white housing lock again and disconnect the connector.
NOTICE:
Do not push down the part (A) shown in the illustration when disconnecting the connector.
|
(d) Remove the bolt and disengage the claw to remove the side No. 2 airbag sensor. |
|
(e) Check that the position of the white housing lock is as shown in the illustration.
|
*a |
Correct |
*b |
Incorrect |
|
|