Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM100000001T514
Model Year Start: 2021 Model: Camry Prod Date Range: [10/2020 -           ]
Title: SUPPLEMENTAL RESTRAINT SYSTEMS: SIDE AIRBAG SENSOR (for Front Door): REMOVAL; 2021 - 2024 MY Camry [10/2020 -        ]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during door side airbag sensor removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Disconnect cable from negative battery terminal

Perform steering sensor zero point calibration

Lane tracing assist system

2021 - 2024 MY Camry [10/2020 -        ]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Pre-collision system

Memorize steering angle neutral point

Parking assist monitor system

2018 - 2024 MY Camry [03/2017 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION

Panoramic view monitor system

2021 - 2024 MY Camry [10/2020 -        ]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: INITIALIZATION

PROCEDURE

1. PRECAUTION

CAUTION:

Be sure to read Precaution thoroughly before servicing.

Click here 2021 - 2022 MY Camry [10/2020 - 08/2022]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: PRECAUTION 2023 - 2024 MY Camry [08/2022 -        ]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here 2020 - 2024 MY Camry [03/2020 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

for A25A-FKS: Click here 2021 - 2024 MY Camry [10/2020 -        ]; MAINTENANCE: A25A-FKS BATTERY: REMOVAL+

for 2GR-FKS: Click here 2021 - 2024 MY Camry [10/2020 -        ]; MAINTENANCE: 2GR-FKS BATTERY: REMOVAL+

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here 2021 - 2022 MY Camry [10/2020 - 08/2022]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION 2023 - 2024 MY Camry [08/2022 -        ]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION

3. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH

Click here 2021 - 2024 MY Camry [10/2020 -        ]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+

4. REMOVE FRONT DOOR ARMREST COVER SUB-ASSEMBLY

Click here 2021 - 2024 MY Camry [10/2020 -        ]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+

5. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)

Click here 2021 - 2024 MY Camry [10/2020 -        ]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+

6. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)

Click here 2021 - 2024 MY Camry [10/2020 -        ]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+

7. REMOVE FRONT ARMREST ASSEMBLY

Click here 2021 - 2024 MY Camry [10/2020 -        ]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+

8. REMOVE FRONT DOOR TRIM PLATE (w/o Courtesy Light)

Click here 2021 - 2024 MY Camry [10/2020 -        ]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+

9. REMOVE COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)

Click here 2018 - 2024 MY Camry [03/2017 -        ]; LIGHTING (INT): DOOR COURTESY LIGHT: REMOVAL+

10. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

Click here 2021 - 2024 MY Camry [10/2020 -        ]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+

11. REMOVE FRONT DOOR SERVICE HOLE COVER

Click here 2021 - 2024 MY Camry [10/2020 -        ]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+

12. REMOVE DOOR SIDE AIRBAG SENSOR

(a) Check that the ignition switch is off.

(b) Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(c) Disconnect the connector from the door side airbag sensor.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.

(1) Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)

*a

White Housing Lock

*b

Yellow CPA

*c

Connector lock is released

-

-

(2) Push down the white housing lock again and disconnect the connector.

NOTICE:

Do not push down the part (A) shown in the illustration when disconnecting the connector.

(d) Remove the nut and disengage the claw to remove the door side airbag sensor.

(e) Check that the position of the white housing lock is as shown in the illustration.

*a

Incorrect

*b

Correct