Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM100000001T510
Model Year Start: 2021 Model: Camry Prod Date Range: [10/2020 -           ]
Title: SUPPLEMENTAL RESTRAINT SYSTEMS: REAR SEAT SIDE AIRBAG ASSEMBLY (for Fold Down Seat Type): REMOVAL; 2021 - 2024 MY Camry [10/2020 -        ]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear seat airbag assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Disconnect cable from negative battery terminal

Perform steering sensor zero point calibration

Lane tracing assist system

2021 - 2024 MY Camry [10/2020 -        ]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Pre-collision system

Memorize steering angle neutral point

Parking assist monitor system

2018 - 2024 MY Camry [03/2017 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION

Panoramic view monitor system

2021 - 2024 MY Camry [10/2020 -        ]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: INITIALIZATION

CAUTION:

  • Be sure to read Precaution thoroughly before servicing.

    Click here 2021 - 2022 MY Camry [10/2020 - 08/2022]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: PRECAUTION 2023 - 2024 MY Camry [08/2022 -        ]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: PRECAUTION

  • Wear protective gloves. Sharp areas on the parts may injure your hands.

NOTICE:

If a rear seat airbag assembly has been deployed, replace the rear seat airbag assembly, rear side seatback frame sub-assembly, rear side seatback pad and rear side seatback cover sub-assembly with the necessary parts in accordance with the extent of the collision damage.

Click here 2020 - 2024 MY Camry [09/2019 -        ]; SEAT: REAR SEAT ASSEMBLY (for Fold Down Seat Type): DISASSEMBLY

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here 2020 - 2024 MY Camry [03/2020 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

for A25A-FKS: Click here 2021 - 2024 MY Camry [10/2020 -        ]; MAINTENANCE: A25A-FKS BATTERY: REMOVAL+

for 2GR-FKS: Click here 2021 - 2024 MY Camry [10/2020 -        ]; MAINTENANCE: 2GR-FKS BATTERY: REMOVAL+

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here 2021 - 2022 MY Camry [10/2020 - 08/2022]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION 2023 - 2024 MY Camry [08/2022 -        ]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION

3. REMOVE REAR SEAT CUSHION ASSEMBLY

Click here 2021 - 2024 MY Camry [10/2020 -        ]; SEAT: REAR SEAT ASSEMBLY (for Fold Down Seat Type): REMOVAL+

4. REMOVE REAR SEAT CUSHION LOCK HOOK

Click here 2021 - 2024 MY Camry [10/2020 -        ]; SEAT: REAR SEAT ASSEMBLY (for Fold Down Seat Type): REMOVAL+

5. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

HINT:

Disconnect the rear door opening trim weatherstrip to the extent that allows the removal of the rear side seatback assembly.

6. REMOVE REAR SIDE SEATBACK ASSEMBLY

Click here 2021 - 2024 MY Camry [10/2020 -        ]; SEAT: REAR SEAT ASSEMBLY (for Fold Down Seat Type): REMOVAL+

7. REMOVE REAR SEAT SHOULDER BELT GUIDE

Click here 2020 - 2024 MY Camry [09/2019 -        ]; SEAT: REAR SEAT ASSEMBLY (for Fold Down Seat Type): DISASSEMBLY+

8. REMOVE REAR SIDE SEATBACK COVER WITH PAD

Click here 2020 - 2024 MY Camry [09/2019 -        ]; SEAT: REAR SEAT ASSEMBLY (for Fold Down Seat Type): DISASSEMBLY+

9. REMOVE REAR SEAT AIRBAG ASSEMBLY

CAUTION:

When storing the rear seat airbag assembly, keep the airbag deployment side facing upward.

Deployment Side

(a) Disengage the clamp.

(b) Disconnect the wire harness from the wire harness clamp.

(c) Remove the 2 nuts and rear seat airbag assembly.

NOTICE:

  • Do not reuse the nuts.
  • Make sure that the rear side seatback frame sub-assembly is not deformed. If it is deformed, replace it with a new one.