| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM100000001T50K |
| Model Year Start: 2021 | Model: Camry | Prod Date Range: [10/2020 - ] |
| Title: SUPPLEMENTAL RESTRAINT SYSTEMS: KNEE AIRBAG ASSEMBLY (for Driver Side): REMOVAL; 2021 - 2024 MY Camry [10/2020 - ] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during lower No. 1 instrument panel airbag assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
Disconnect cable from negative battery terminal |
Perform steering sensor zero point calibration |
Lane tracing assist system |
|
|
Pre-collision system |
|||
|
Memorize steering angle neutral point |
Parking assist monitor system |
|
|
|
Panoramic view monitor system |
|
PROCEDURE
1. PRECAUTION
CAUTION:
Be sure to read Precaution thoroughly before servicing.
Click here
![2021 - 2022 MY Camry [10/2020 - 08/2022]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: PRECAUTION](/t3Portal/stylegraphics/info.gif)
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here
2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
for A25A-FKS: Click here
for 2GR-FKS: Click here
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here
3. REMOVE FRONT DOOR SCUFF PLATE LH
Click here
4. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH
Click here
5. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH
HINT:
Disconnect the front door opening trim weatherstrip LH to the extent that allows the removal of the instrument side panel LH.
6. REMOVE INSTRUMENT SIDE PANEL LH
Click here
7. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Click here
8. REMOVE NO. 2 METER HOOD CLUSTER
Click here
9. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
Click here
10. REMOVE NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY
Click here
11. REMOVE NO. 1 METER HOOD CLUSTER
Click here
12. REMOVE LOWER CENTER INSTRUMENT PANEL FINISH PANEL
Click here
13. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY
CAUTION:
When storing the lower No. 1 instrument panel airbag assembly, keep the airbag deployment side facing upward.
|
Deployment Side |
(a) Check that the ignition switch is off.
(b) Check that the cable is disconnected from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
|
(c) Remove the 4 bolts. |
|
|
(d) Disengage the 2 claws and separate the lower No. 1 instrument panel airbag assembly. NOTICE: When separating the lower No. 1 instrument panel airbag assembly, do not pull the airbag wire harness. |
|
|
*a |
Protective Tape |
|
*b |
Airbag Connector |
|
*c |
Airbag Connector Locking Button |
|
Release in this Direction |
(e) Using a screwdriver with its tip wrapped with protective tape, release the airbag connector locking button.
(f) Disconnect the airbag connector to remove the lower No. 1 instrument panel airbag assembly.
NOTICE:
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
|
|