| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM100000001SH6E |
| Model Year Start: 2021 | Model: Camry | Prod Date Range: [10/2020 - ] |
| Title: CRUISE CONTROL: FRONT CAMERA SYSTEM: U030051,U030057; Internal Control Module Software Incompatibility Not Programmed; 2021 - 2024 MY Camry [10/2020 - ] | ||
|
DTC |
U030051 |
Internal Control Module Software Incompatibility Not Programmed |
|
DTC |
U030057 |
Internal Control Module Software Incompatibility Invalid/Incompatible Software Component |
DESCRIPTION
The forward recognition camera receives vehicle information from the ECM via the CAN communication line.
When the forward recognition camera is unable to determine the vehicle information from the vehicle information sent from the ECM, the forward recognition camera outputs U030051.
When the vehicle information sent from the ECM does not match the vehicle information stored by the forward recognition camera, the forward recognition camera outputs U030057.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
|---|---|---|---|
|
U030051 |
Internal Control Module Software Incompatibility Not Programmed |
The forward recognition camera cannot confirm the vehicle information from the ECM. |
|
|
U030057 |
Internal Control Module Software Incompatibility Invalid/Incompatible Software Component |
The vehicle information from the ECM and that stored in the forward recognition camera do not match. |
|
CAUTION / NOTICE / HINT
NOTICE:
- When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
-
When the forward recognition camera is replaced with a new one or the windshield glass is replaced or removed/installed, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history for each system.
HINT:
Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.
One Time Recognition: Click here
![2021 - 2024 MY Camry [10/2020 - ]; CRUISE CONTROL: FRONT CAMERA: TARGET ADJUSTMENT(ONE TIME RECOGNITION)](/t3Portal/stylegraphics/info.gif)
Sequential Recognition: Click here
Driving Adjustment: Click here
-
When replacing the ECM, refer to Registration.
w/ Smart Key System: Click here
w/o Smart Key System: Click here
PROCEDURE
|
1. |
CHECK FOR DTCs |
(a) Check for DTCs.
Powertrain > Engine > Trouble Codes
|
Result |
Proceed to |
|---|---|
|
SFI system DTC is not output |
A |
|
SFI system DTC is output |
B |
| B |
|
GO TO SFI SYSTEM for A25A-FKS: Click here
for 2GR-FKS: Click here
|
|
|
2. |
CHECK FOR DTCs (HEALTH CHECK) |
(a) Using the Techstream, perform a health check.
OK:
ECUs other than the forward recognition camera do not output specification information mismatch DTCs related to the ECM.
|
Result |
Proceed to |
|---|---|
|
DTC is not output |
A |
|
DTC is output |
B |
| B |
|
REPLACE ECM for A25A-FKS: Click here
for 2GR-FKS: Click here
|
|
|
3. |
READ VALUE USING TECHSTREAM |
(a) Using the Techstream, read the Data List.
Chassis > Front Recognition Camera > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
HV/EV Equipped Information |
Vehicle information (engine) stored by forward recognition camera |
Non-HV/EV or HV/EV |
Non-HV/EV: Gasoline Model HV/EV: HV Model |
If a display different from vehicle specification is output, a forward recognition camera that was used with a different vehicle was installed, or the forward recognition camera may be malfunctioning. |
Chassis > Front Recognition Camera > Data List
|
Tester Display |
|---|
|
HV/EV Equipped Information |
HINT:
- When the specification stored by the forward recognition camera and the vehicle specification do not match, there is a malfunction in the specification information stored by the forward recognition camera. Therefore, replace the forward recognition camera.
- When the specification stored by the forward recognition camera and the vehicle specification match, an ECM with different specifications may be installed. Therefore, replace the ECM.
|
Result |
Proceed to |
|---|---|
|
Specification stored by the forward recognition camera and vehicle specification do not match |
A |
|
Specification stored by the forward recognition camera and vehicle specification match |
B |
| A |
|
| B |
|
REPLACE ECM for A25A-FKS: Click here
for 2GR-FKS: Click here
|
|
|