Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM100000001SB3S
Model Year Start: 2021 Model: Camry Prod Date Range: [10/2020 -           ]
Title: EXTERIOR PANELS / TRIM: FRONT BUMPER: REMOVAL; 2021 - 2024 MY Camry [10/2020 -        ]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front bumper assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

*1: Applies only for when removing and installing or replacing the rear television camera assembly.

Front bumper assembly (w/ Panoramic view monitor system)

Front television camera view adjustment

Panoramic View Monitor System

2021 - 2024 MY Camry [10/2020 -        ]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: INITIALIZATION for Initialization

2021 - 2024 MY Camry [10/2020 -        ]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: CALIBRATION for Calibration

Replacement or removal and installation of 2 or more parts:

  • Front television camera assembly, front bumper assembly or radiator grille
  • Rear television camera assembly
  • Side television camera assembly LH or outer rear view mirror assembly LH
  • Side television camera assembly RH or outer rear view mirror assembly RH
  • Television camera view adjustment
  • Rear television camera assembly optical axis (Back camera detection function)*1

HINT:

When the front bumper is damaged or deformed due to an accident or contact with other objects, etc., or the bumper installation area on the body is repaired, it is necessary to perform millimeter wave radar sensor adjustment.

Target Adjustment (Triangle Target):

Click here 2021 - 2024 MY Camry [10/2020 -        ]; CRUISE CONTROL: MILLIMETER WAVE RADAR SENSOR: TARGET ADJUSTMENT(TRIANGLE TARGET)

Target Adjustment (Flat Surface Target):

Click here 2021 - 2024 MY Camry [10/2020 -        ]; CRUISE CONTROL: MILLIMETER WAVE RADAR SENSOR: TARGET ADJUSTMENT(FLAT SURFACE TARGET)

Driving Adjustment:

Click here 2021 - 2024 MY Camry [10/2020 -        ]; CRUISE CONTROL: MILLIMETER WAVE RADAR SENSOR: DRIVING ADJUSTMENT

PROCEDURE

1. REMOVE COOL AIR INTAKE DUCT SEAL

(a) Remove the 5 clips.

(b) Disengage the guide and remove the cool air intake duct seal as shown in the illustration.

Remove in this Direction (1)

Remove in this Direction (2)

2. REMOVE FRONT BUMPER ASSEMBLY

(a) Apply protective tape around the front bumper assembly as shown in the illustration.

Protective Tape

(b) Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws as shown in the illustration.

*a

Protective Tape

Insert Screwdriver Here

Remove in this Direction

HINT:

Use the same procedure for the RH side and LH side.

(c) Remove the clip.

HINT:

Use the same procedure for the RH side and LH side.

(d) Remove the 8 screws.

(e) Disengage the 3 claws as shown in the illustration.

Place Hand Here

Remove in this Direction

HINT:

Use the same procedure for the RH side and LH side.

(f) w/ Pre-collision System:

(1) Disconnect the connector.

(g) w/ Parking Support Brake System:

(1) Disconnect the connector.

(h) Remove the 2 clips.

(i) Remove the 4 bolts.

(j) Disengage the 2 claws and 2 guides to remove the front bumper assembly as shown in the illustration.

Remove in this Direction