Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM100000001SAR4
Model Year Start: 2021 Model: Camry Prod Date Range: [10/2020 -           ]
Title: BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM (w/ Electric Parking Brake System): C050C14; Left Rear Wheel Speed Sensor Circuit Short to Ground or Open; 2021 - 2024 MY Camry [10/2020 -        ]

DTC

C050C14

Left Rear Wheel Speed Sensor Circuit Short to Ground or Open

DESCRIPTION

Refer to DTC C050C12

Click here 2021 - 2024 MY Camry [10/2020 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM (w/ Electric Parking Brake System): C050C12; Left Rear Wheel Speed Sensor Circuit Short to Battery+

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

C050C14

Left Rear Wheel Speed Sensor Circuit Short to Ground or Open

A short or open circuit is detected in the speed sensor signal circuit for 0.12 seconds or more.
  • Rear speed sensor LH (rear axle hub and bearing assembly LH)*1
  • Rear speed sensor LH*2
  • Wire harness or connector
  • Skid control sensor wire LH (No. 2 parking brake wire assembly)
  • Skid control ECU (brake actuator assembly)

*1: for 2WD

*2: for AWD

DTC Detection Conditions: C050C14

 

Vehicle Condition

Pattern 1

Pattern 2

Diagnosis Condition

-

-

-

Malfunction Status

An open circuit is detected in the speed sensor signal circuit.

○

-

A short circuit is detected in the speed sensor signal circuit.

-

○

Detection Time

0.12 seconds or more.

0.12 seconds or more.

Number of Trips

1 trip

1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.

WIRING DIAGRAM

Refer to DTC C050C12.

Click here 2021 - 2024 MY Camry [10/2020 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM (w/ Electric Parking Brake System): C050C12; Left Rear Wheel Speed Sensor Circuit Short to Battery+

CAUTION / NOTICE / HINT

NOTICE:

  • After replacing the skid control ECU (brake actuator assembly), perform acceleration sensor zero point calibration and system information memorization.

    Click here 2021 MY Camry [10/2020 - 08/2021]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM (w/ Electric Parking Brake System): CALIBRATION 2022 - 2024 MY Camry [08/2021 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM (w/ Electric Parking Brake System): CALIBRATION

  • After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

    Click here 2021 MY Camry [10/2020 - 08/2021]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM (w/ Electric Parking Brake System): TEST MODE PROCEDURE 2022 - 2024 MY Camry [08/2021 -        ]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM (w/ Electric Parking Brake System): TEST MODE PROCEDURE

PROCEDURE

1.

CHECK VEHICLE

(a) Check the vehicle specification.

Result

Proceed to

for 2WD

A

for AWD

B
B

GO TO STEP 7

A

2.

CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)

(a) Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.

*a

Front view of skid control sensor wire LH (No. 2 parking brake wire assembly)

(to Rear Speed Sensor LH (Rear Axle Hub and Bearing Assembly LH))

(b) Disconnect the v2 rear speed sensor LH (rear axle hub and bearing assembly LH) connector.

(c) Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.

(d) Turn the ignition switch to ON.

(e) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

v2-2 (LA+) - v2-1 (LA-)

Ignition switch on

11 to 14 V
NG

GO TO STEP 5

OK

3.

INSPECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

(a) Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.

*a

Front view of skid control sensor wire LH (No. 2 parking brake wire assembly)

*b

Front view of wire harness connector

(to Sensor Side Connector)

*c

Front view of wire harness connector

(to Vehicle Side Connector)

(b) Disconnect the v2 skid control sensor wire LH (No. 2 parking brake wire assembly) connector.

(c) Disconnect the vR1 skid control sensor wire LH (No. 2 parking brake wire assembly) connector.

(d) Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.

(e) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

v2-1 (LA-) or vR1-2 (RL-) - Body ground and other terminals

Always

10 kΩ or higher
NG

REPLACE NO. 2 PARKING BRAKE WIRE ASSEMBLY
OK

4.

CHECK HARNESS AND CONNECTOR (NO. 2 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

(a) Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.

(b) Disconnect the A34 skid control ECU (brake actuator assembly) connector.

(c) Disconnect the vR1 skid control sensor wire LH (No. 2 parking brake wire assembly) connector.

(d) Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.

(e) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

vR1-2 (RL-) or A34-23 (RL-) - Body ground

Always

10 kΩ or higher
OK

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.

INSPECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

(a) Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.

*a

Front view of skid control sensor wire LH (No. 2 parking brake wire assembly)

*b

Front view of wire harness connector

(to Sensor Side Connector)

*c

Front view of wire harness connector

(to Vehicle Side Connector)

(b) Disconnect the v2 skid control sensor wire LH (No. 2 parking brake wire assembly) connector.

(c) Disconnect the vR1 skid control sensor wire LH (No. 2 parking brake wire assembly) connector.

(d) Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.

(e) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

v2-1 (LA-) - vR1-2 (RL-)

Always

Below 1 Ω
NG

REPLACE NO. 2 PARKING BRAKE WIRE ASSEMBLY
OK

6.

CHECK HARNESS AND CONNECTOR (NO. 2 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

(a) Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.

(b) Disconnect the A34 skid control ECU (brake actuator assembly) connector.

(c) Disconnect the vR1 skid control sensor wire LH (No. 2 parking brake wire assembly) connector.

(d) Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.

(e) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

vR1-2 (RL-) - A34-23 (RL-)

Always

Below 1 Ω
OK

REPLACE BRAKE ACTUATOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.

CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)

(a) Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.

*a

Front view of skid control sensor wire LH (No. 2 parking brake wire assembly)

(to Rear Speed Sensor LH)

(b) Disconnect the v2 rear speed sensor LH connector.

(c) Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.

(d) Turn the ignition switch to ON.

(e) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

v2-2 (LA+) - v2-1 (LA-)

Ignition switch on

11 to 14 V
NG

GO TO STEP 5

OK

8.

INSPECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

(a) Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.

*a

Front view of skid control sensor wire LH (No. 2 parking brake wire assembly)

*b

Front view of wire harness connector

(to Sensor Side Connector)

*c

Front view of wire harness connector

(to Vehicle Side Connector)

(b) Disconnect the v2 skid control sensor wire LH (No. 2 parking brake wire assembly) connector.

(c) Disconnect the vR1 skid control sensor wire LH (No. 2 parking brake wire assembly) connector.

(d) Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.

(e) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

v2-1 (LA-) or vR1-2 (RL-) - Body ground and other terminals

Always

10 kΩ or higher
NG

REPLACE NO. 2 PARKING BRAKE WIRE ASSEMBLY
OK

9.

CHECK HARNESS AND CONNECTOR (NO. 2 PARKING BRAKE WIRE ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

(a) Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.

(b) Disconnect the A34 skid control ECU (brake actuator assembly) connector.

(c) Disconnect the vR1 skid control sensor wire LH (No. 2 parking brake wire assembly) connector.

(d) Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.

(e) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

vR1-2 (RL-) or A34-23 (RL-) - Body ground

Always

10 kΩ or higher
OK

REPLACE REAR SPEED SENSOR LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR