Last Modified: 11-20-2023 |
6.11:8.1.0 |
Doc ID: RM100000001SAIX |
Model Year Start: 2021 |
Model: Camry |
Prod Date Range: [10/2020 -
] |
Title: BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM (w/ Electric Parking Brake System): C05061F; Right Front Wheel Speed Sensor Circuit Intermittent; 2021 - 2024 MY Camry [10/2020 - ] |
DTC
|
C05061F
|
Right Front Wheel Speed Sensor Circuit Intermittent
|
DESCRIPTION
Refer to DTC C050612
Click here
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
C05061F
|
Right Front Wheel Speed Sensor Circuit Intermittent
|
-
The speed sensor signal is excessively noisy.
-
The calculated change in wheel speed is more than 980 m/s2 for 5*1 or 20*2 seconds or more.
-
The calculated change in wheel speed fluctuates between more than 500 m/s2 and less than -500 m/s2 for 5*1 or 20*2 seconds or more.
-
When the vehicle speed is low, excessive noise in the speed sensor pulse signal is detected 3 times or more within 0.005 seconds for 5*1 or 20*2 seconds or more.
|
-
Front speed sensor RH
-
Front speed sensor rotor RH (front axle hub sub-assembly RH)
|
-
*1: The stop light switch assembly is OFF.
-
*2: The stop light switch assembly is ON.
DTC Detection Conditions: C05061F
|
Vehicle Condition
|
Pattern 1
|
Pattern 2
|
Pattern 3
|
Pattern 4
|
Diagnosis Condition
|
The Stop light switch assembly is OFF.
|
-
|
○
|
○
|
○
|
Malfunction Status
|
The speed sensor signal is excessively noisy.
|
○
|
-
|
-
|
-
|
The calculated change in wheel speed is more than 980 m/s2.
|
-
|
○
|
-
|
-
|
The calculated change in wheel speed fluctuates between more than 500 m/s2 and less than -500 m/s2.
|
-
|
-
|
○
|
-
|
The vehicle speed is low, excessive noise in the speed sensor pulse signal is detected 3 times or more within 0.005 seconds.
|
-
|
-
|
-
|
○
|
Detection Time
|
-
|
5 seconds or more.
|
5 seconds or more.
|
5 seconds or more.
|
Number of Trips
|
1 trip
|
1 trip
|
1 trip
|
1 trip
|
HINT:
DTC will be output when conditions for either of the patterns in the table above are met.
DTC Detection Conditions: C05061F
|
Vehicle Condition
|
Pattern 5
|
Pattern 6
|
Pattern 7
|
Diagnosis Condition
|
The stop light switch assembly is ON.
|
○
|
○
|
○
|
Malfunction Status
|
The calculated change in wheel speed is more than 980 m/s2.
|
○
|
-
|
-
|
The calculated change in wheel speed fluctuates between more than 500 m/s2 and less than -500 m/s2.
|
-
|
○
|
-
|
The vehicle speed is low, excessive noise in the speed sensor pulse signal is detected 3 times or more within 0.005 seconds.
|
-
|
-
|
○
|
Detection Time
|
20 seconds or more.
|
20 seconds or more.
|
20 seconds or more.
|
Number of Trips
|
1 trip
|
1 trip
|
1 trip
|
HINT:
DTC will be output when conditions for either of the patterns in the table above are met.
CAUTION / NOTICE / HINT
NOTICE:
-
After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.
Click here
-
After replacing or removing and installing a speed sensor rotor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.
Click here
-
DTC precaution
Click here
Procedure to clear warning lights (When not clearing DTCs)
Procedure
|
-
Repair or replacement.
-
Turn the ignition switch to ON.
-
Drive the vehicle at 54 km/h (34 mph) or more for 3 seconds or more to clear the warning lights.
|
PROCEDURE
1.
|
CHECK FRONT SPEED SENSOR RH (CHECK FOR FOREIGN MATTER)
|
(a) Remove the front speed sensor RH.
Click here
(b) Check the front speed sensor RH.
OK:
The front speed sensor RH tip is free of oil and foreign matter.
HINT:
If foreign matter of 1mm x 1mm or more is adhered to the front speed sensor RH, this DTC may be stored.
OK
|
|
|
2.
|
CHECK FRONT SPEED SENSOR ROTOR RH (CHECK FOR FOREIGN MATTER)
|
(a) Remove the component with the front speed sensor rotor RH.
Click here
(b) Check the front speed sensor rotor RH.
OK:
The front speed sensor rotor RH is free of oil and foreign matter.
HINT:
If foreign matter of 1mm x 1mm or more is adhered to the front speed sensor rotor RH, this DTC may be stored.
OK |
|
REPLACE FRONT SPEED SENSOR RH AND FRONT AXLE HUB SUB-ASSEMBLY RH
for front speed sensor RH: Click here
for front speed sensor rotor RH (front axle hub sub-assembly RH): Click here
|
NG
|
|
|
3.
|
CLEAN FRONT SPEED SENSOR ROTOR RH
|
(a) Clean the front speed sensor rotor RH.
NOTICE:
Do not use parts cleaner when cleaning the front speed sensor rotor RH.
NEXT
|
|
|
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Operate the Techstream to clear the codes. Enter the following menus: Chassis / Brake/EPB / Trouble Codes.
Chassis > Brake > Clear DTCs
(d) Press the DTC clear button.
NEXT
|
|
|
5.
|
PERFORM DEALER MODE (SIGNAL CHECK) INSPECTION (SPEED SENSOR CHECK)
|
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Using the Techstream, perform a Dealer Mode (Signal Check) inspection sensor check and check that speed sensor Dealer Mode (Signal Check) inspection items change from incomplete to complete. Enter the following menus: Chassis / Brake/EPB / Utility / Signal Check.
Click here
Chassis > Brake > Utility
Tester Display
|
Signal Check
|
OK:
Speed sensor Dealer Mode (Signal Check) inspection items change from incomplete to complete.
NG |
|
REPLACE FRONT SPEED SENSOR RH AND FRONT AXLE HUB SUB-ASSEMBLY RH
for front speed sensor RH: Click here
for front speed sensor rotor RH (front axle hub sub-assembly RH): Click here
|
OK
|
|
|
(a) Connect the Techstream to the DLC3.
(b) Start the engine.
(c) Perform a road test under the same malfunction conditions recreated based on the Freeze Frame Data or customer problem analysis.
(d) Read the DTCs following the prompts on the Techstream. Enter the following menus: Chassis / Brake/EPB / Trouble Codes.
Chassis > Brake > Trouble Codes
(e) Check if the same DTC is output.
Result
|
Proceed to
|
C05061F is not output
|
A
|
C05061F is output
|
B
|
A |
|
END
|
B |
|
REPLACE FRONT SPEED SENSOR RH AND FRONT AXLE HUB SUB-ASSEMBLY RH
for front speed sensor RH: Click here
for front speed sensor rotor RH (front axle hub sub-assembly RH): Click here
|
7.
|
CLEAN FRONT SPEED SENSOR RH
|
(a) Clean the front speed sensor RH.
NOTICE:
When cleaning the front speed sensor RH, make sure to clean the installation hole before installation.
NEXT
|
|
|
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Operate the Techstream to clear the codes. Enter the following menus: Chassis / Brake/EPB / Trouble Codes.
Chassis > Brake > Clear DTCs
(d) Press the DTC clear button.
NEXT
|
|
|
9.
|
PERFORM DEALER MODE (SIGNAL CHECK) INSPECTION (SPEED SENSOR CHECK)
|
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Using the Techstream, perform a Dealer Mode (Signal Check) inspection sensor check and check that speed sensor Dealer Mode (Signal Check) inspection items change from incomplete to complete. Enter the following menus: Chassis / Brake/EPB / Utility / Signal Check.
Click here
Chassis > Brake > Utility
Tester Display
|
Signal Check
|
OK:
Speed sensor Dealer Mode (Signal Check) inspection items change from incomplete to complete.
OK
|
|
|
(a) Connect the Techstream to the DLC3.
(b) Start the engine.
(c) Perform a road test under the same malfunction conditions recreated based on the Freeze Frame Data or customer problem analysis.
(d) Read the DTCs following the prompts on the Techstream. Enter the following menus: Chassis / Brake/EPB / Trouble Codes.
Chassis > Brake > Trouble Codes
(e) Check if the same DTC is output.
Result
|
Proceed to
|
C05061F is not output
|
A
|
C05061F is output
|
B
|
A |
|
END
|
|