Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM100000001S9C2
Model Year Start: 2021 Model: Camry Prod Date Range: [10/2020 -           ]
Title: A25A-FKS (ENGINE CONTROL): SFI SYSTEM: P161009; Control Module Processor (Brake Override System Input Signal) Component Failure; 2021 - 2024 MY Camry [10/2020 -        ]

DTC

P161009

Control Module Processor (Brake Override System Input Signal) Component Failure

DESCRIPTION

The ECM monitors for malfunction displays during brake override system input information (stop light switch assembly, speed sensor) malfunctions.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Memory

Note

P161009

Control Module Processor (Brake Override System Input Signal) Component Failure

Any of the following conditions are met (1 trip detection logic).

  • Malfunction in ECM internal RAM for stop light switch assembly
  • When a malfunction in the ECM internal RAM for the speed sensor causes the slowest speed value among the 4 wheels to be 7 km/h (4.3 mph) or less and the second slowest speed value among the 4 wheels to be 40 km/h (24.9 mph) or higher for 5 seconds

ECM

Does not come on

DTC stored
  • SAE Code: P1610
  • DTC for Mexico Models: Applies

MONITOR DESCRIPTION

The ECM compares input signal information for brake override system control calculations for control and monitoring. If the ECM determines a malfunction mode in which brake override system operation conditions are not met, a DTC is stored to indicate the brake override system malfunction.

MONITOR STRATEGY

Required Sensors/Components

Stop light switch assembly

Speed sensor

Frequency of Operation

Continuous

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the Techstream on.
  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  5. Turn the Techstream off.
  6. Turn the ignition switch off and wait for at least 30 seconds.
  7. Turn the ignition switch to ON [A].
  8. Turn the Techstream on.
  9. Start the engine.
  10. Drive the vehicle at 40 km/h (25 mph) or more for 60 seconds or more [B].

    CAUTION:

    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  11. Enter the following menus: Powertrain / Engine / Trouble Codes [C].
  12. Read the pending DTCs.

    HINT:

    • If a pending DTC is output, the system is malfunctioning.
    • If a pending DTC is not output, perform the following procedure.
  13. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  14. Input the DTC: P161009.
  15. Check the DTC judgment result.

    Techstream Display

    Description

    NORMAL
    • DTC judgment completed
    • System normal

    ABNORMAL
    • DTC judgment completed
    • System abnormal

    INCOMPLETE
    • DTC judgment not completed
    • Perform driving pattern after confirming DTC enabling conditions

    HINT:

    • If the judgment result is NORMAL, the system is normal.
    • If the judgment result is ABNORMAL, the system is malfunctioning.
    • If the judgment result is INCOMPLETE, perform steps [A] through [C].

CAUTION / NOTICE / HINT

HINT:

Read Freeze Frame Data using the Techstream. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE

1.

CLEAR DTC

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Clear the DTCs.

Powertrain > Engine > Clear DTCs

(e) Turn the ignition switch off and wait for at least 30 seconds.

NEXT

2.

READ OUTPUT DTC (DTC P161009)

(a) Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

(b) Enter the following menus: Powertrain / Engine / Trouble Codes.

(c) Read the DTCs.

Powertrain > Engine > Trouble Codes

Result

Proceed to

DTCs are not output

A

DTC P161009 is output

B
A

CHECK FOR INTERMITTENT PROBLEMS

B

REPLACE ECM 2021 - 2022 MY Camry [10/2020 - 08/2022]; A25A-FKS (ENGINE CONTROL): ECM: REMOVAL 2023 - 2024 MY Camry [08/2022 -        ]; A25A-FKS (ENGINE CONTROL): ECM: REMOVAL