Last Modified: 11-20-2023 |
6.11:8.1.0 |
Doc ID: RM100000001S7V3 |
Model Year Start: 2021 |
Model: Camry |
Prod Date Range: [10/2020 -
] |
Title: PARKING BRAKE: ELECTRIC PARKING BRAKE SYSTEM: C061013; Right Electric Parking Brake Actuator Control Circuit Open; 2021 - 2024 MY Camry [10/2020 - ] |
DTC
|
C061013
|
Right Electric Parking Brake Actuator Control Circuit Open
|
DESCRIPTION
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
Memory
|
Note
|
C061013
|
Right Electric Parking Brake Actuator Control Circuit Open
|
-
Diagnosis Condition:
Electric parking brake not operating
-
Malfunction Status:
The ECU power supply is normal but there is a malfunction in the electric parking brake actuator RH internal circuit (open).
-
Detection Time:
Approximately 0.015 to 0.195 seconds (depending on each malfunction)
|
-
Parking brake actuator assembly RH
-
No. 1 parking brake wire assembly
-
Wire harness or connector
-
Skid control ECU (brake actuator assembly)
|
DTC stored
|
An electric parking brake system malfunction is displayed on the multi-information display.
|
WIRING DIAGRAM
Click here
PROCEDURE
1.
|
INSPECT NO. 1 PARKING BRAKE WIRE ASSEMBLY
|
(a) Turn the ignition switch off.
(b) Make sure that there is no looseness at the locking part and the connecting part of the connectors.
OK:
The connector is securely connected.
(c) Disconnect the uR2 and u1 No. 1 parking brake wire assembly connectors.
(d) Check both the connector case and the terminals for deformation and corrosion.
OK:
No deformation or corrosion.
(e) Measure the resistance according to the value(s) in the table below.
*a
|
Front view of No. 1 Parking Brake Wire Assembly
|
*b
|
(to wire harness connector)
|
*c
|
(to Parking Brake Actuator Assembly RH)
|
-
|
-
|
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
uR2-2 - u1-2 (RE+)
|
Always
|
Below 1 Ω
|
uR2-2 - Other terminals
|
Always
|
10 kΩ or higher
|
uR2-1 - u1-1 (RE-)
|
Always
|
Below 1 Ω
|
uR2-1 - Other terminals
|
Always
|
10 kΩ or higher
|
NG |
|
REPLACE NO. 1 PARKING BRAKE WIRE ASSEMBLY
|
OK
|
|
|
2.
|
CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY RH)
|
(a) Turn the ignition switch off.
(b) Make sure the No. 1 parking brake wire assembly is securely installed.
(c) Disconnect the A34 skid control ECU (brake actuator assembly) connector.
(d) Disconnect the u1 parking brake actuator assembly RH connector.
(e) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
A34-2 (MRR+) - u1-2 (RE+)
|
Always
|
Below 1 Ω
|
A34-3 (MRR-) - u1-1 (RE-)
|
Always
|
Below 1 Ω
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
3.
|
INSPECT PARKING BRAKE ACTUATOR ASSEMBLY RH
|
(a) Remove the parking brake actuator assembly RH.
Click here
(b) Inspect the parking brake actuator assembly RH.
Click here
|