Last Modified: 11-20-2023 |
6.11:8.1.0 |
Doc ID: RM100000001S7V0 |
Model Year Start: 2021 |
Model: Camry |
Prod Date Range: [10/2020 -
] |
Title: PARKING BRAKE: ELECTRIC PARKING BRAKE SYSTEM: C060E2A; Left Electric Parking Brake Actuator Signal Stuck In Range; 2021 - 2024 MY Camry [10/2020 - ] |
DTC
|
C060E2A
|
Left Electric Parking Brake Actuator Signal Stuck In Range
|
DESCRIPTION
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
Memory
|
Note
|
C060E2A
|
Left Electric Parking Brake Actuator Signal Stuck In Range
|
-
Diagnosis Condition:
Electric parking brake operating
-
Malfunction Status:
Motor locked, gear locked, free spinning, repeated slipping
-
Detection Time:
-
|
-
Parking brake actuator assembly LH
-
No. 2 parking brake wire assembly
-
Wire harness or connector
-
Rear brake LH
|
DTC stored
|
An electric parking brake system malfunction is displayed on the multi-information display.
|
DTC Detection Conditions
|
Vehicle Condition
|
Pattern 1
|
Pattern 2
|
Pattern 3
|
Pattern 4
|
Diagnosis Condition
|
Electric parking brake operating
|
○
|
○
|
○
|
○
|
Malfunction Status
|
Motor lock detected
|
○
|
-
|
-
|
-
|
Gear lock detected
|
-
|
○
|
-
|
-
|
Free spinning detected
|
-
|
-
|
○
|
-
|
Repeated slipping detected
|
-
|
-
|
-
|
○
|
Detection Time
|
-
|
-
|
-
|
-
|
Number of Trips
|
1 trip
|
1 trip
|
1 trip
|
1 trip
|
WIRING DIAGRAM
Click here
CAUTION / NOTICE / HINT
NOTICE:
-
Although DTC C060E2A may be stored after entering pad replacement mode, this is not a malfunction.
-
Although DTC C060E2A may be stored after forcibly releasing the parking brake, this is not a malfunction.
PROCEDURE
(a) Using the Techstream, check for DTCs other than DTC C060E2A.
Chassis > Brake > Trouble Codes
Result
|
Proceed to
|
Only DTC C060E2A is output
|
A
|
DTCs other than C060E2A are output
|
B
|
A
|
|
|
2.
|
INSPECT NO. 2 PARKING BRAKE WIRE ASSEMBLY
|
(a) Turn the ignition switch off.
(b) Make sure that there is no looseness at the locking part and the connecting part of the connectors.
OK:
The connector is securely connected.
(c) Disconnect the vR2 and v1 No. 2 parking brake wire assembly connectors.
(d) Check both the connector case and the terminals for deformation and corrosion.
OK:
No deformation or corrosion.
(e) Measure the resistance according to the value(s) in the table below.
*a
|
Front view of No. 2 Parking Brake Wire Assembly
|
*b
|
(to wire harness connector)
|
*c
|
(to Parking Brake Actuator Assembly LH)
|
-
|
-
|
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
vR2-2 - v1-2 (LE+)
|
Always
|
Below 1 Ω
|
vR2-2 or v1-2 (LE+) - Body ground and other terminals
|
Always
|
10 kΩ or higher
|
vR2-1 - v1-1 (LE-)
|
Always
|
Below 1 Ω
|
vR2-1 or v1-1 (LE-) - Body ground and other terminals
|
Always
|
10 kΩ or higher
|
NG |
|
REPLACE NO. 2 PARKING BRAKE WIRE ASSEMBLY
|
OK
|
|
|
3.
|
CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - PARKING BRAKE ACTUATOR ASSEMBLY LH)
|
(a) Turn the ignition switch off.
(b) Make sure the No. 2 parking brake wire assembly is securely installed.
(c) Disconnect the A34 skid control ECU (brake actuator assembly) connector.
(d) Disconnect the v1 parking brake actuator assembly LH connector.
(e) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
A34-13 (MRL+) - v1-2 (LE+)
|
Always
|
Below 1 Ω
|
A34-12 (MRL-) - v1-1 (LE-)
|
Always
|
Below 1 Ω
|
A34-13 (MRL+) or v1-2 (LE+) - Body ground
|
Always
|
10 kΩ or higher
|
A34-12 (MRL-) or v1-1 (LE-) - Body ground
|
Always
|
10 kΩ or higher
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
4.
|
INSPECT REAR BRAKE AND PARKING BRAKE ACTUATOR ASSEMBLY LH (CHECK FOR ROTATING PARTS THAT ARE STUCK AND FOR FREE SPINNING ACTUATORS)
|
(a) Enter rear brake pad replacement mode.
Click here
(b) Turn the ignition switch off.
(c) Check that the rotating parts are not seized or the actuator is not spinning freely.
(1) Check that the parking brake actuator assembly LH is installed properly to the rear brake caliper and that it is not spinning freely.
For the parking brake actuator assembly LH removal procedure: Click here
(2) Check that there is no damage to the rotating parts from the parking brake actuator assembly LH to the rear brake caliper.
(3) Inspect the parking brake actuator assembly LH and check that it operates correctly.
Click here
(4) Check that the rear brake caliper threaded part rotates and that the rear disc brake piston moves outward.
HINT:
For the check procedures, refer to the parking brake forced release method when not using the Techstream.
Click here
HINT:
Return to normal mode after work is complete.
Click here
Result
|
Proceed to
|
Parking brake actuator assembly LH is malfunctioning
|
A
|
Other than parking brake actuator assembly LH is malfunctioning
|
B
|
B |
|
REPAIR OR REPLACE ABNORMAL PARTS
|
|