A25A-FKS (ENGINE MECHANICAL): ENGINE UNIT: INSTALLATION; 2021 - 2024 MY Camry [10/2020

Last Modified: 11-20-2023	6.11:8.1.0	Doc ID: RM100000001RZ17
Model Year Start: 2021	Model: Camry	Prod Date Range: [10/2020 - ]
Title: A25A-FKS (ENGINE MECHANICAL): ENGINE UNIT: INSTALLATION; 2021 - 2024 MY Camry [10/2020 - ]

INSTALLATION

CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click here

PROCEDURE

1. INSTALL NO. 2 VACUUM SWITCHING VALVE BRACKET

(a) Using an 8 mm socket wrench, install the No. 2 vacuum switching valve bracket to the cylinder head sub-assembly with the 2 bolts.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

2. INSTALL PURGE VALVE (PURGE VSV)

Click here

3. INSTALL NO. 3 EXHAUST MANIFOLD HEAT INSULATOR

(a) Install the No. 3 exhaust manifold heat insulator to the cylinder block sub-assembly with the bolt.

Torque:

16 N·m {163 kgf·cm, 12 ft·lbf}

4. INSTALL ENGINE WATER PUMP ASSEMBLY (WATER INLET HOUSING)

(a) Install the engine water pump assembly (water inlet housing) and a new gasket to the cylinder block sub-assembly with 4 bolts.

Torque:

43 N·m {438 kgf·cm, 32 ft·lbf}

5. INSTALL WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

Click here

6. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

(a) Apply a light coat of engine oil to a new O-ring.

(b) Install the O-ring to the engine oil level dipstick guide.

(c) Using an 8 mm socket wrench, install the engine oil level dipstick guide to the camshaft housing sub-assembly with the bolt.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

(d) Install the engine oil level dipstick.

7. INSTALL IGNITION COIL ASSEMBLY

Click here

8. INSTALL DIRECT FUEL INJECTOR ASSEMBLY

Click here

9. INSTALL FUEL DELIVERY PIPE

Click here

10. INSTALL PORT FUEL INJECTOR ASSEMBLY

Click here

11. INSTALL NO. 5 ENGINE WIRE

Click here

12. INSTALL INJECTOR VIBRATION INSULATOR

Click here

13. INSTALL NO. 1 DELIVERY PIPE SPACER

Click here

14. INSTALL FUEL DELIVERY PIPE WITH SENSOR SUB-ASSEMBLY

Click here

15. INSTALL WIRE HARNESS CLAMP BRACKET

(a) Using an 8 mm socket wrench, install the wire harness clamp bracket to the No. 1 ventilation case with the 2 bolts.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

16. INSTALL NO. 6 ENGINE WIRE

(a) Install the No. 6 engine wire to the wire harness clamp bracket with the 2 nuts.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

(b) Engage the 2 clamps.

17. INSTALL SENSOR WIRE

(a) Using an 8 mm socket wrench, install the sensor wire to the water inlet with thermostat sub-assembly with the bolt.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

(b) Engage the 3 clamps.

18. INSTALL NO. 7 WATER BY-PASS HOSE

(a) Install the No. 7 water by-pass hose and slide the 2 clips to secure it.

19. TEMPORARILY INSTALL FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY (for High Pressure)

Click here

20. TEMPORARILY INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

Click here

21. INSTALL FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY (for High Pressure)

Click here

22. INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

(a) Using a 17 mm union nut wrench, tighten the union nut on the fuel delivery pipe side of the No. 1 fuel pipe sub-assembly.

Torque:

Specified tightening torque :

35 N·m {357 kgf·cm, 26 ft·lbf}

NOTICE:

Do not adjust the torque in the loosening direction.

HINT:

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click here
When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)

*a	17 mm Union Nut Wrench
*b	Torque Wrench Fulcrum Length

(b) Using a 17 mm union nut wrench, tighten the union nut on the fuel pump assembly side of the No. 1 fuel pipe sub-assembly.

Torque:

Specified tightening torque :

35 N·m {357 kgf·cm, 26 ft·lbf}

NOTICE:

Do not adjust the torque in the loosening direction.

HINT:

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click here
When using a 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 30 N*m (306 kgf*cm, 22 ft.*lbf)

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

23. CONNECT FUEL TUBE SUB-ASSEMBLY

Click here

24. INSTALL NO. 1 INTAKE MANIFOLD TO HEAD GASKET

Click here

25. INSTALL INTAKE MANIFOLD

Click here

26. INSTALL NO. 2 WATER BY-PASS PIPE

(a) Install the bolt (A).

Torque:

21 N·m {214 kgf·cm, 15 ft·lbf}

(b) Using an 8 mm socket wrench, install the No. 2 water by-pass pipe with the 2 bolts (B) in the order shown in the illustration.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

27. INSTALL NO. 3 WATER BY-PASS PIPE

(a) Connect the No. 3 water by-pass pipe to the water outlet and slide the clip to secure it.

(b) Using an 8 mm socket wrench, install the No. 3 water by-pass pipe to the intake manifold with the bolt.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

28. INSTALL EGR VALVE ASSEMBLY

(a) Align and fit the hole of the EGR valve assembly to the pin of the camshaft housing sub-assembly.

*a	Pin
*b	Hole

(b) Using an 8 mm socket wrench, install the EGR valve assembly with the 2 bolts.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

29. INSTALL WATER HOSE

(a) Connect the water hose to the EGR valve assembly and slide the clip to secure it.

30. INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY

(a) Using an 8 mm socket wrench, install the No. 1 EGR pipe sub-assembly, a new EGR inlet gasket and EGR valve adapter gasket with the 4 bolts.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

31. INSTALL EGR COOLER ASSEMBLY

(a) Install a new EGR cooler gasket to the EGR cooler assembly.

NOTICE:

Make sure that the claws of the EGR cooler gasket are toward the EGR cooler assembly side.

Claw

(b) Install a new EGR valve gasket to the EGR cooler assembly.

NOTICE:

Make sure that the claws of the EGR valve gasket are toward the EGR valve assembly side.

(1) Temporarily install the EGR cooler assembly to the cylinder head sub-assembly and EGR valve assembly with the 2 bolts and 3 nuts.

	Bolt
	Nut

(2) Tighten the 2 bolts and 3 nuts in the order shown in the illustration.

Torque:

24 N·m {245 kgf·cm, 18 ft·lbf}

(d) Type B:

(1) Temporarily install the EGR cooler assembly to the cylinder head sub-assembly and EGR valve assembly with the 3 bolts and 2 nuts.

	Bolt
	Nut

(2) Tighten the 3 bolts and 2 nuts in the order shown in the illustration.

Torque:

24 N·m {245 kgf·cm, 18 ft·lbf}

(e) Connect the No. 3 water by-pass hose to the EGR cooler assembly.

(f) Connect the water hose to the EGR cooler assembly.

32. INSTALL THROTTLE BODY GASKET

Click here

33. INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

Click here

34. INSTALL EXHAUST MANIFOLD (TWC: Front Catalyst)

Click here

35. INSTALL MANIFOLD STAY

Click here

36. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

(a) Type A:

(1) Install the No. 1 exhaust manifold heat insulator to the exhaust manifold (TWC: Front Catalyst) with the 5 bolts.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

(b) Type B:

(1) Install the No. 1 exhaust manifold heat insulator to the exhaust manifold (TWC: Front Catalyst) with the 3 bolts.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

37. INSTALL FLOW SHUTTING VALVE (WATER BY-PASS HOSE ASSEMBLY)

(a) Install the flow shutting valve (water by-pass hose assembly) to the water by-pass outlet sub-assembly and slide the clip to secure it.

NOTICE:

Make sure to slide the flow shutting valve (water by-pass hose assembly) until it contacts the hose stopper of the water by-pass outlet sub-assembly.
Make sure that the claws of the clip are within the location shown in the illustration.

*a	Paint Mark
*b	45° (Claw of Clip Location)

(b) Install the water hose clamp bracket with the 2 bolts.

Torque:

13 N·m {133 kgf·cm, 10 ft·lbf}

Torque:

19 N·m {194 kgf·cm, 14 ft·lbf}

38. INSTALL NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

(a) Install the No. 2 water by-pass pipe sub-assembly with the bolt.

Torque:

19 N·m {194 kgf·cm, 14 ft·lbf}

(b) Connect the No. 2 water by-pass pipe sub-assembly to the outlet water by-pass sub-assembly and slide the clip to secure it.

39. INSTALL NO. 3 TIMING CHAIN COVER (w/ Cover)

(a) Using an 8 mm socket wrench, install the No. 3 timing chain cover and plate washer to the No. 2 timing gear cover assembly with the bolt.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

40. INSTALL TIMING GEAR COVER INSULATOR

(a) Using an 8 mm socket wrench, install the timing gear cover insulator and plate washer to the No. 2 timing gear cover assembly with the bolt.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

41. INSTALL NO. 2 TIMING CHAIN COVER INSULATOR

(a) Install the No. 2 timing chain cover insulator to the V-ribbed belt tensioner assembly.

42. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

NOTICE:

Do not apply or add any oil or grease to the belt tensioner to prevent abnormal noises from the belt tensioner pulley, belt squealing, etc.
Do not allow oil or grease to adhere to the moving parts of the belt tensioner, as this may cause malfunctions.

If oil or grease is on the location indicated by the arrow, replace the V-ribbed belt tensioner assembly.

(a) Install the V-ribbed belt tensioner assembly to the No. 2 timing gear cover assembly with the 2 bolts.

Torque:

21 N·m {214 kgf·cm, 15 ft·lbf}

43. INSTALL NO. 2 ENGINE COVER

(a) Install the No. 2 engine cover to the No. 2 timing gear cover assembly with the 2 bolts.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

44. INSTALL COMPRESSOR ASSEMBLY WITH PULLEY

(a) for Type A:

(1) Using an E8 "TORX" socket wrench, temporarily install the compressor assembly with pulley with the 2 stud bolts.

Torque:

5.0 N·m {51 kgf·cm, 44 in·lbf}

(2) Install the compressor assembly with pulley with the 2 bolts and 2 nuts.

	Bolt
	Nut

Torque:

24.5 N·m {250 kgf·cm, 18 ft·lbf}

HINT:

Tighten the bolts and nuts in the order shown in the illustration.

(b) for Type B:

(1) Install the compressor assembly with pulley with the 4 bolts.

Torque:

24.5 N·m {250 kgf·cm, 18 ft·lbf}

HINT:

Tighten the bolts in the order shown in the illustration.

45. INSTALL GENERATOR ASSEMBLY

Click here

46. INSTALL V-RIBBED BELT

Click here

47. INSTALL DRIVE SHAFT BEARING BRACKET

(a) Install the drive shaft bearing bracket with the 3 bolts.

Torque:

63.7 N·m {650 kgf·cm, 47 ft·lbf}

NOTICE:

Make sure that the bolts and bolt holes are free of oil. Clean them if necessary.