Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM100000001RIKF
Model Year Start: 2021 Model: Camry Prod Date Range: [10/2020 -           ]
Title: PARK ASSIST / MONITORING: INTUITIVE PARKING ASSIST SYSTEM: C1AE987; Ultrasonic Sensor (Rear Right Corner) Missing Message; 2021 - 2024 MY Camry [10/2020 -        ]

DTC

C1AE987

Ultrasonic Sensor (Rear Right Corner) Missing Message

DESCRIPTION

This DTC is stored when an open circuit or short occurs in the communication line between the rear corner ultrasonic sensor RH and the clearance warning ECU assembly, or when a malfunction occurs in the rear corner ultrasonic sensor RH.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

C1AE987

Ultrasonic Sensor (Rear Right Corner) Missing Message

Rear corner ultrasonic sensor RH lost communication

  • Rear corner ultrasonic sensor RH
  • Harness or connector
  • Clearance warning ECU assembly

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • Perform registration after replacing or removing and installing the ultrasonic sensor or clearance warning ECU assembly.

    Click here 2021 - 2024 MY Camry [10/2020 -        ]; PARK ASSIST / MONITORING: INTUITIVE PARKING ASSIST SYSTEM: CALIBRATION

  • If a DTC is detected again after the repair, turn the ignition switch to ON and turn the intuitive parking assist system on, and then clear the DTC.

    Click here 2021 - 2024 MY Camry [10/2020 -        ]; PARK ASSIST / MONITORING: INTUITIVE PARKING ASSIST SYSTEM: DTC CHECK / CLEAR

PROCEDURE

1.

VEHICLE CONDITION AND WORK DETAILS CHECK

(a) Check the vehicle condition and work details.

Result

Proceed to

The clearance warning ECU assembly or ultrasonic sensor has not been replaced

A

The clearance warning ECU assembly or ultrasonic sensor has been replaced

B

B

GO TO CALIBRATION

A

2.

CHECK CONNECTOR CONNECTION CONDITION (ULTRASONIC SENSOR)

(a) Check that the connector is properly connected to the rear corner ultrasonic sensor and rear center ultrasonic sensor.

NEXT

3.

CHECK FOR DTC

(a) According to the display on the GTS, check for DTCs.

Body Electrical > Clearance Warning > Trouble Codes

(b) According to the display on the GTS, clear the DTCs.

Body Electrical > Clearance Warning > Clear DTCs

(c) Recheck for DTCs.

Body Electrical > Clearance Warning > Trouble Codes

Result

Proceed to

C1AE987 is not output

A

C1AE987 is output

B

A

END (CONNECTOR CONNECTION MALFUNCTION)

B

4.

CHECK CONNECTOR CONNECTION CONDITION (CLEARANCE WARNING ECU ASSEMBLY)

(a) Check that the connector is properly connected to the clearance warning ECU assembly.

NEXT

5.

CHECK FOR DTC

(a) According to the display on the GTS, check for DTCs.

Body Electrical > Clearance Warning > Trouble Codes

(b) According to the display on the GTS, clear the DTCs.

Body Electrical > Clearance Warning > Clear DTCs

(c) Recheck for DTCs.

Body Electrical > Clearance Warning > Trouble Codes

DTC OUTPUT COMBINATION:

Symptoms

DTC Detection

C1AE987

C1AE887

C1AE787

C1AE687

Symptom 1

Not output

Not output

Not output

Not output

Symptom 2

Output

Output

Output

Output

Symptom 3

Not output

Output

Output

Output

Symptom 4

Not output

Not output

Output

Output

Symptom 5

Not output

Not output

Not output

Output

Symptom 6

Output

Not output

Not output

Not output

Result

Proceed to

Listed under symptom 1 in combination table

A

Listed under symptom 2 in combination table

B

Listed under symptom 3 in combination table

C

Listed under symptom 4 in combination table

D

Listed under symptom 5 in combination table

E

Listed under symptom 6 in combination table

F

A

USE SIMULATION METHOD TO CHECK 2021 MY Camry [10/2020 - 08/2021]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2022 - 2024 MY Camry [08/2021 -        ]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING

C

GO TO CORRESPONDING FLOWCHART (INTUITIVE PARKING ASSIST SYSTEM (C1AE887))

D

GO TO CORRESPONDING FLOWCHART (INTUITIVE PARKING ASSIST SYSTEM (C1AE787))

E

GO TO CORRESPONDING FLOWCHART (INTUITIVE PARKING ASSIST SYSTEM (C1AE687))

F

GO TO STEP 7

B

6.

CHECK WIRE HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - REAR CORNER ULTRASONIC SENSOR RH)

(a) Disconnect the R39 clearance warning ECU assembly connector.

(b) Disconnect the X5 rear corner ultrasonic sensor RH connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

R39-19 (BOR) - X5-4 (BI)

Always

Below 1 Ω

R39-21 (SOR) - X5-5 (SI)

Always

Below 1 Ω

R39-20 (E1) - X5-6 (EI)

Always

Below 1 Ω

R39-19 (BOR) or X5-4 (BI) - Body ground

Always

10 kΩ or higher

R39-21 (SOR) or X5-5 (SI) - Body ground

Always

10 kΩ or higher

R39-20 (E1) or X5-6 (EI) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE WIRE HARNESS OR CONNECTOR

OK

7.

REPLACE REAR CORNER ULTRASONIC SENSOR RH

(a) Replace the rear corner ultrasonic sensor RH with a new or normally functioning one.

Click here 2021 - 2024 MY Camry [10/2020 -        ]; PARK ASSIST / MONITORING: ULTRASONIC SENSOR (for Rear): REMOVAL

HINT:

To check if the ultrasonic sensor is functioning correctly, replace it with another ultrasonic sensor.

NEXT

8.

CHECK FOR DTC

(a) According to the display on the GTS, check for DTCs.

Body Electrical > Clearance Warning > Trouble Codes

(b) According to the display on the GTS, clear the DTCs.

Body Electrical > Clearance Warning > Clear DTCs

(c) Recheck for DTCs.

Body Electrical > Clearance Warning > Trouble Codes

Result

Proceed to

No DTC is output

A

"C1AE987" is output

B

A

END (REAR CORNER ULTRASONIC SENSOR RH WAS DEFECTIVE)

B

REPLACE CLEARANCE WARNING ECU ASSEMBLY