Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM100000001RE7Z
Model Year Start: 2021 Model: Camry Prod Date Range: [10/2020 -           ]
Title: PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: DATA LIST / ACTIVE TEST; 2021 - 2024 MY Camry [10/2020 -        ]

DATA LIST / ACTIVE TEST

DATA LIST

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Chassis / Circumference Monitoring Camera Control Module / Data List.

(e) Read the Data List according to the display on the Techstream.

Chassis > Panoramic View Monitor > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Main CPU Forced Termination Detection Record

A history item indicating that the main CPU did not enter standby status within 15 seconds of turning the ignition switch off and a forced end was applied

Unrec/Rec

Unrec: Television camera controller is normal

Rec: Television camera controller is abnormal

-

Main CPU Abnormal Response Record

A history item indicating that the main CPU became unresponsive in normal status

Unrec/Rec

Unrec: Television camera controller is normal

Rec: Television camera controller is abnormal

-

Main CPU Abnormal Reset Record

A history item indicating that the main CPU was reset, although the ignition switch was not turned off in normal status

Unrec/Rec

Unrec: Television camera controller is normal

Rec: Television camera controller is abnormal

-

Image Processing IC Written Protect Record

A history item indicating that the image processing IC memory was write protected

Unrec/Rec

Unrec: Television camera controller is normal

Rec: Television camera controller is abnormal

-

Image Processing IC Initialized Malfunction Record

A history item indicating that the image processing IC memory was not initialized

Unrec/Rec

Unrec: Television camera controller is normal

Rec: Television camera controller is abnormal

-

Main EEPROM Access Status

Main EEPROM access status

OK/NG

OK: Television camera controller is normal

NG: Television camera controller is abnormal

-

Sub EEPROM Access Status

Sub-EEPROM access status

OK/NG

OK: Television camera controller is normal

NG: Television camera controller is abnormal

-

System Power Supply Voltage Malfunction Record

A history item indicating an abnormally generated-voltage value from the system power source

Unrec/Rec

Unrec: Television camera controller is normal

Rec: Television camera controller is abnormal

-

Main CPU Starting Malfunction Record

A history item indicating that the main CPU did not start

Unrec/Rec

Unrec: Television camera controller is normal

Rec: Television camera controller is abnormal

-

CAN CPU Boot Malfunction Record

A history item indicating that the CPU controlling the input and output of the information obtained via the CAN communication system did not start and the information could not be retrieved

Unrec/Rec

Unrec: Television camera controller is normal

Rec: Television camera controller is abnormal

-

Wheel Speed Sensor (4wheel)

Reception state of the vehicle speed signal from the skid control ECU

OK/NG

OK: Speed signal received

NG: Speed signal not received

-

Continuous Bus Off

Continuous bus off status (Global)

Not Detected/Detected

Not detected: Communication condition available

Detected: Communication condition not available

-

Image Adjustment Status

Status of the image adjustment status

Incomplete/Processing/Complete

Incomplete: Image adjustment incomplete

Processing: Image adjustment in processing

Complete: Image adjustment completed

-

Number of DTC

Number of DTCs (past and present)

Min: 0, Max: 255

Number of DTCs will be displayed

-