Display does not switch when the panoramic view monitor switch is pressed.

Proceed to "ECU Power Source Circuit"

Diagnostic mode - Signal connection check (CAMERA SW check)

Television camera controller

Display does not switch to the panoramic view and rear view screen, wide rear view screen, or narrow rear view screen when the shift lever is in R.

Diagnostic mode - Signal connection check (SHIFT check)

Reverse signal circuit

Television camera controller

Image not displayed on the panoramic view and rear view screen, wide rear view screen or narrow rear view screen when the shift lever is in R.

Proceed to "Image from Camera for Panoramic View Monitor is Abnormal"

Display does not switch to the see through view screen or moving view screen when the panoramic view monitor switch is pressed.

Diagnostic mode - Signal connection check (CAN check)

Diagnostic mode - Signal connection check (CAMERA SW check)

Television camera controller

Image not displayed on the see through view screen or moving view screen when the panoramic view monitor switch is pressed.

Proceed to "Image from Camera for Panoramic View Monitor is Abnormal"

Display does not switch to the panoramic view and wide front view screen or the two-side view screen when the panoramic view monitor switch is pressed.

Diagnostic mode - Signal connection check (CAN check)

Diagnostic mode - Signal connection check (CAMERA SW check)

Television camera controller

Image not displayed on the panoramic view and wide front view screen or side clearance view screen when the panoramic view monitor main switch is pressed.

Proceed to "Image from Camera for Panoramic View Monitor is Abnormal"

Display does not switch to the retracted screen when the outer mirrors are retracted.

Diagnostic mode - Signal connection check (CAN check)

Television camera controller

Display does not switch from the retracted screen when the outer mirrors are not in the retracted position.

Diagnostic mode - Signal connection check (CAN check)

Television camera controller

Objects not displayed correctly on the panoramic view monitor screen (color, distorted image).

Proceed to "Image from Camera for Panoramic View Monitor is Abnormal"

Distorted display on panoramic view screen.

Camera view adjustment (calibration)

Television camera controller

Parking lines do not match at front and rear on panoramic view screen.

Camera view adjustment (calibration)

Television camera controller

Partial black screen on panoramic view screen.

Proceed to "Image from Camera for Panoramic View Monitor is Abnormal"

Camera view adjustment (calibration)

Television camera controller

Area displayed differs from the actual area.

Ensure no door is opened

-

Camera view adjustment (calibration)

Television camera controller

Panoramic view monitor switch night illumination does not illuminate.

Inspect panoramic view monitor switch

Harness or connector

-

Touch switch operation does not work for any system.

Navigation system - Touch switch self check*1

Audio and visual system - Touch switch self check*2

Television camera controller

Radio and display receiver assembly

The touch function of the screen does not operate for the panoramic view monitor system.

Television camera controller

Radio and display receiver assembly

When the vehicle speed increases in the automatic display mode, the panoramic view and wide front view screen or the two-side view screen remains displayed, without switching to the navigation screen.

Television camera controller

The screen display timer function does not operate if the manual display mode is selected.

Check the screen display timer function

-

Television camera controller

The estimated course lines do not match the vehicle width extension lines when the steering wheel points straight ahead.

Check the steering wheel installation angle

Adjust steering angle

Camera view adjustment (calibration)

Television camera controller

Estimated course lines stop moving before the steering wheel is turned fully left.

Steering angle setting (calibrate stored maximum steering angle)

"!" is displayed and estimated course lines are not displayed.

Check that the luggage compartment door is not open

-

Television camera controller

Radio and display receiver assembly

Estimated course lines are not displayed.

Check the panoramic view monitor screen display mode settings (Check if the estimated course lines display is set to off)

Television camera controller

"!" is displayed.

Store the steering angle sensor steering neutral point

Diagnostic mode - Signal connection check (CAN check)

-

Check that the electric parking brake system is operating normally

-

"!" remains displayed after the steering neutral point is stored.

Adjust steering angle

Steering sensor

Television camera controller

"!" is displayed and all the buttons on the screen are grayed out.

Camera view adjustment (calibration)

Adjust steering angle

Refer to Navigation System*1

Refer to Audio and Visual System*2

"!" is displayed and all the buttons on the screen are grayed out even after television camera controller initialization has been completed.

Television camera controller

Refer to Navigation System*1

Refer to Audio and Visual System*2

Guide lines and buttons are not displayed on the panoramic view and rear view screen display screen.

Check that the luggage compartment door is not open

-

Check if the luggage light turns on and off normally (If not, refer to Lighting System (Interior) - Problem Symptoms Table)

Television camera controller

"CHK" is displayed for an item on the Vehicle Signal Check screen.

Diagnostic mode - Signal connection check

Blind spots in image.

Ensure no door is opened

-

Camera view adjustment (calibration)

Camera boundary lines are poorly connected.

Camera view adjustment (calibration)

Estimated course lines are displaced.

Camera view adjustment (calibration)

Adjust steering angle

All buttons on the panoramic view monitor are continuously grayed out

Refer to Navigation System*1

Refer to Audio and Visual System*2

When adjusting the camera optical axis, "You can not calibrate the camera when the door is open. Please close the door." is displayed even after the luggage compartment door has been closed

Check if the luggage light turns on and off normally (If not, refer to Lighting System (INT) - Problem Symptoms Table)

Television camera controller

When the parking assist monitor screen is displayed, "RCD unavailable" is displayed.

Correct the steering angle neutral point (Initialization)

Blind spot monitor system

-

Rear television camera assembly

When the parking assist monitor screen is displayed, "RCD malfunction. Visit your dealer" is displayed.

Rear television camera assembly

The indicator does not respond when the mute switch is pushed.

Proceed to "Touch Panel Switch does not Function"*1

Proceed to "Touch Panel Switch does not Function"*2

Rear television camera assembly

Television camera controller

Radio and display receiver assembly

When there is a pedestrian in the detection area, no pedestrian is detected.

Refer to "Notes for Rear Camera Detection Function" in precaution

Perform calibration

Rear television camera assembly

When there is no pedestrian in the detection area, a pedestrian is detected.

Refer to "Notes for Rear Camera Detection Function" in precaution

Perform calibration

Rear television camera assembly

A pedestrian who is in the absolute no detection area is detected.

Perform calibration

Rear television camera assembly

A pedestrian is only detected when they are in the absolute detection area.

Perform calibration

Rear television camera assembly