SUPPLEMENTAL RESTRAINT SYSTEMS: CENTER AIRBAG SENSOR ASSEMBLY: INSTALLATION; 2020 - 2024 MY Camry [03/2020

Last Modified: 11-20-2023	6.11:8.1.0	Doc ID: RM100000001NNZP
Model Year Start: 2020	Model: Camry	Prod Date Range: [03/2020 - ]
Title: SUPPLEMENTAL RESTRAINT SYSTEMS: CENTER AIRBAG SENSOR ASSEMBLY: INSTALLATION; 2020 - 2024 MY Camry [03/2020 - ]

INSTALLATION

PROCEDURE

1. INSTALL AIRBAG SENSOR ASSEMBLY

(a) Check that the ignition switch is off.

(b) Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(c) Install the airbag sensor assembly with the 3 bolts.

Torque:

17.5 N·m {178 kgf·cm, 13 ft·lbf}

NOTICE:

Temporarily tighten the 2 bolts in the order of (A), (B) and then fully tighten the 3 bolts in the order of (C), (A) and (B).
If the airbag sensor assembly has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.
When installing the airbag sensor assembly, make sure that the SRS wiring does not interfere with or is not pinched between other parts.
When the ignition switch is first turned to ON after the airbag sensor assembly has been replaced, make sure that no one is in the vehicle.

(d) Temporarily connect the connector and then move the lock lever in the direction indicated by the arrow to securely connect the connectors.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.

*a	Lock Lever
	Move in this Direction

(e) Check that there is no looseness in the installed parts of the airbag sensor assembly.

2. INSTALL NO. 1 CONSOLE BOX DUCT (for Dual Type)

Click here

3. INSTALL FRONT FLOOR CARPET ASSEMBLY

Click here

4. INSTALL ACCELERATOR PEDAL

for A25A-FKS: Click here

for 2GR-FKS: Click here

5. INSTALL ACCELERATOR PEDAL PAD

for A25A-FKS: Click here

for 2GR-FKS: Click here

6. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Click here

7. INSTALL LOWER CENTER PILLAR GARNISH LH

Click here

8. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH

9. INSTALL REAR DOOR SCUFF PLATE LH

Click here

10. CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

11. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH

Click here

12. INSTALL FRONT DOOR SCUFF PLATE LH

Click here

13. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Click here

14. INSTALL LOWER CENTER PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.

Click here

15. CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH

16. INSTALL REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

Click here

17. CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

18. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

Click here

19. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

Click here

20. INSTALL REAR SEAT CUSHION LOCK HOOK

for Fold Down Seat Type: Click here

for Fixed Seat Type: Click here

21. INSTALL REAR SEAT CUSHION ASSEMBLY

for Fold Down Seat Type: Click here

for Fixed Seat Type: Click here

22. INSTALL CONSOLE BOX ASSEMBLY

Click here

23. INSTALL FRONT SEAT ASSEMBLY LH

for Manual Seat: Click here

for Power Seat: Click here

24. INSTALL FRONT SEAT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

for Manual Seat: Click here

for Power Seat: Click here

25. PERFORM DIAGNOSTIC SYSTEM CHECK

Click here

26. PERFORM YAW RATE AND ACCELERATION SENSOR ZERO POINT CALIBRATION

(a) When the airbag sensor assembly is replaced, perform zero point learning for the yaw rate and acceleration sensor.

w/o Electric Parking Brake System: Click here

w/ Electric Parking Brake System: Click here

for Dynamic Torque Control AWD System: Click here