A25A-FKS (COOLING): FLOW SHUTTING VALVE (for ATF): REMOVAL; 2020 MY Camry [03/2020

Last Modified: 11-20-2023	6.11:8.1.0	Doc ID: RM100000001NC35
Model Year Start: 2020	Model: Camry	Prod Date Range: [03/2020 - 10/2020]
Title: A25A-FKS (COOLING): FLOW SHUTTING VALVE (for ATF): REMOVAL; 2020 MY Camry [03/2020 - 10/2020]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during flow shutting valve (No. 1 water by-pass hose) removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed	Link
Battery terminal is disconnected/reconnected	Perform steering sensor zero point calibration	Lane departure alert system (w/ Steering Control)
		Pre-collision system
		Intelligent clearance sonar system*4
	Memorize steering angle neutral point	Parking assist monitor system
	Memorize steering angle neutral point	Panoramic view monitor system
Replacement of ECM	Vehicle Identification Number (VIN) registration	MIL comes on
Replacement of ECM	ECU communication ID registration (Immobiliser system)	Engine start function	1 2
Replacement of ECM (If possible, read the transaxle compensation code from the previous ECM)	Reset memory*3 Transfer transaxle compensation code Perform road test to allow ECM to learn	Large shift shock Deterioration of fuel efficiency	for UB80E Initialization for UB80E Registration for UB80F Initialization for UB80F Registration
Replacement of ECM (If impossible, read the transaxle compensation code from the previous ECM)	Reset memory*3 Reset transaxle compensation code Perform road test to allow ECM to learn	Large shift shock Deterioration of fuel efficiency
Replacement of ECM*1	Code registration (Smart key System (for Start Function)	Wireless door lock control system Smart key system (for Entry Function) Smart key system (for Start Function) Steering lock function
Replacement of ECM*2	Code registration (Immobiliser system (w/o Smart Key System))	Wireless door lock control system Engine start

*1: w/ Smart Key System
*2: w/o Smart Key System
*3: When the ECM is replaced with a new one, reset memory is unnecessary.
*4: When performing learning using the Techstream.
Click here

PROCEDURE

1. REMOVE BATTERY

Click here

2. REMOVE ECM

Click here

3. REMOVE BATTERY CLAMP SUB-ASSEMBLY

Click here

4. REMOVE FRONT WHEEL LH

5. REMOVE FRONT WHEEL OPENING EXTENSION PAD RH

Click here

6. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH

Click here

7. REMOVE NO. 1 ENGINE UNDER COVER

Click here

8. REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY

Click here

9. REMOVE FRONT FENDER APRON SEAL LH

Click here

10. DRAIN ENGINE COOLANT

Click here

11. REMOVE FLOW SHUTTING VALVE (NO. 1 WATER BY-PASS HOSE)

(a) Disengage the 3 clamps to remove the transmission breather clamp.

(b) Disengage the 3 clamps to remove the hose clamp.

(c) Disengage the 2 clamps to disconnect the flow shutting valve (No. 1 water by-pass hose) and transmission breather hose from the hose clamp.

(d) Slide the clip and disconnect the flow shutting valve (No. 1 water by-pass hose) from the water outlet.

HINT:

Use a container to catch any engine coolant which flows out of the flow shutting valve (No. 1 water by-pass hose) and water outlet.

(e) Slide the clip and disconnect the flow shutting valve (No. 1 water by-pass hose) from the transmission oil cooler.

HINT:

Use a container to catch any engine coolant which flows out of the flow shutting valve (No. 1 water by-pass hose) and transmission oil cooler.

(f) Disconnect the flow shutting valve connector.

(g) Remove the bolt and flow shutting valve (No. 1 water by-pass hose).