A25A-FKS (ENGINE MECHANICAL): REAR CRANKSHAFT OIL SEAL: REMOVAL; 2020 MY Camry [03/2020

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear crankshaft oil seal removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Battery terminal is disconnected/reconnected

Perform steering sensor zero point calibration

Lane departure alert system (w/ Steering Control)

Pre-collision system

Intelligent clearance sonar system*

Memorize steering angle neutral point

Parking Assist Monitor System

Panoramic view monitor system

Replacement of ECM

Vehicle Identification Number (VIN) registration

MIL comes on

ECU communication ID registration (Immobiliser system)

Engine start function

Gas leak from exhaust system is repaired

Inspection After Repair

Poor idle, etc.
Engine start function, etc.

Replacement of automatic transaxle assembly

Reset memory
Input transaxle compensation code into ECM
Perform road test to allow ECM to learn

Large shift shock
Deterioration of fuel efficiency

for UB80E Initialization

for UB80E Registration

for UB80F Initialization

for UB80F Registration

Replacement of ECM

(If possible, read the transaxle compensation code from the previous ECM)

Reset memory*3
Transfer transaxle compensation code
Perform road test to allow ECM to learn

Replacement of ECM

(If impossible, read the transaxle compensation code from the previous ECM)

Reset memory*3
Reset transaxle compensation code
Perform road test to allow ECM to learn

Automatic transaxle fluid

ATF thermal degradation estimate reset

The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly.

for UB80E

for UB80F

Replacement of ECM*1

Code registration (Smart key System (for Start Function))

Wireless door lock control system
Smart key system (for Entry Function)
Smart key system (for Start Function)
Steering lock function

Replacement of ECM*2

Code registration (Immobiliser system (w/o Smart Key System))

Wireless door lock control system
Engine start

Suspension, tires, etc.

(The vehicle height changes because of suspension or tire replacement)

Rear television camera assembly optical axis (Back camera position setting)

Parking assist monitor system

for Initialization:

for Calibration:

Replacement of front bumper assembly (w/ Panoramic view monitor system)

Front television camera view adjustment

Panoramic view monitor system

for Initialization:

for Calibration:

Suspension, tires, etc.

(The vehicle height changes because of suspension or tire replacement)

Television camera controller initialization
Adjust steering angle
Rear television camera assembly optical axis (Back camera position setting)

Front wheel alignment adjustment

Perform system variant learning and acceleration sensor zero point calibration.

VSC disabled or malfunctioning
DTCs are output
Slip indicator light illuminated
ABS warning light illuminated

w/ Electric Parking Brake System:

w/o Electric Parking Brake System:

*1: w/ Smart Key System
*2: w/o Smart Key System
*3: When the ECM is replaced with a new one, reset memory is unnecessary.
*: When performing learning using the Techstream.
Click here

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click here

2020 - 2024 MY Camry [03/2020 - ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

PROCEDURE

for 2WD:
Click here
for AWD:
Click here

(a) Using height adjustment attachments and plate lift attachments, place the engine assembly on a flat level surface.

NOTICE:

Using height adjustment attachments and plate lift attachments, keep the engine assembly level.
To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments under the No. 2 oil pan sub-assembly of the engine assembly.
Using an engine sling device and engine lift, secure the engine assembly before servicing.

Do not damage the surface of the rear engine oil seal press fit hole or the crankshaft.