Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM100000001MVPW
Model Year Start: 2020 Model: Camry Prod Date Range: [03/2020 - 10/2020]
Title: A25A-FKS (FUEL): FUEL SENDER GAUGE ASSEMBLY (for AWD): REMOVAL; 2020 MY Camry [03/2020 - 10/2020]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel sender gauge assembly or No. 2 fuel sender gauge assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

*: When performing learning using the Techstream.

Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; PARK ASSIST / MONITORING: INTELLIGENT CLEARANCE SONAR SYSTEM: CALIBRATION

Battery terminal is disconnected/reconnected

Perform steering sensor zero point calibration.

Lane departure alert system (w/ Steering Control)

2018 - 2020 MY Camry [03/2017 - 10/2020]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Pre-collision system

Intelligent clearance sonar system*

Memorize steering angle neutral point

Parking assist monitor system

2018 - 2024 MY Camry [03/2017 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION

Panoramic view monitor system

2018 - 2020 MY Camry [06/2017 - 10/2020]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: INITIALIZATION

CAUTION:

  • Never perform work on fuel system components near any possible ignition sources.
  • Vaporized fuel could ignite, resulting in a serious accident.
  • Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.
  • Sparks could cause vaporized fuel to ignite, resulting in a serious accident.

PROCEDURE

1. REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

Click here 2020 MY Camry [03/2020 - 10/2020]; A25A-FKS (FUEL): FUEL PUMP (for AWD): REMOVAL

2. REMOVE FUEL SENDER GAUGE ASSEMBLY

(a) Disconnect the fuel sender gauge assembly connector.

(b) Disengage the 3 clamps to disconnect the wire harness from the fuel suction tube with pump and gauge assembly.

NOTICE:

  • Do not damage the wire harness.
  • When disengaging each wire harness from the clamp, disengage one wire at a time.

(c) Disengage the 2 claws to remove the fuel sender gauge assembly from the fuel suction tube with pump and gauge assembly.

NOTICE:

Be careful not to bend the arm of the fuel sender gauge assembly.

3. REMOVE REAR FLOOR SERVICE HOLE COVER

(a) Using a clip remover with its tip wrapped with protective tape, remove the rear floor service hole cover and butyl tape.

*a

Protective Tape

(b) Disconnect the rear fuel main and return tube sub-assembly connector.

4. REMOVE FUEL PUMP GAUGE RETAINER

(a) Disengage the claw to remove the No. 1 fuel tube clamp.

(b) Remove the fuel pump gauge retainer.

(1) Temporarily install SST (plate) and SST (claw) to the fuel pump gauge retainer.

SST: 09808-01071

SST: 09808-14031

09808-01030

09808-01090

HINT:

Securely insert the ends of SST (claw) into the insertion points in the fuel pump gauge retainer.

*a

Insertion Point

*b

SST (Plate)

*c

SST (Claw)

*d

SST (Bolt)

(2) While firmly pressing SST (claw) into the insertion points in the fuel pump gauge retainer, tighten SST (bolt).

(3) Install SST (handle) to SST (plate).

SST: 09808-14031

09808-01010

*a

SST (Handle)

*b

SST (Plate)

*c

SST (Claw)

*d

SST (Bolt)

(4) Lightly press down on SST to prevent it from separating from the fuel pump gauge retainer. While pressing down on SST, rotate SST (handle) slowly to loosen the fuel pump gauge retainer.

NOTICE:

  • Do not use any tools other than specified as this may result in damage to the fuel pump gauge retainer or fuel tank assembly.
  • Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.
  • Make sure to rotate SST (handle) horizontally. If it is rotated at an angle, SST may come off.
  • Do not spin SST too fast or use an impact wrench as this may result in damage to components.
  • If SST comes off of the fuel pump gauge retainer, loosen SST (bolt) and reinstall SST.

(5) While pressing down on the rear fuel main and return tube sub-assembly, remove the fuel pump gauge retainer.

5. REMOVE REAR FUEL MAIN AND RETURN TUBE SUB-ASSEMBLY

(a) Raise the rear fuel main and return tube sub-assembly.

NOTICE:

Be careful not to bend the arm of the No. 2 fuel sender gauge assembly.

(b) Disconnect the fuel return vent tube sub-assembly and remove the rear fuel main and return tube sub-assembly from the fuel tank assembly.

Click here 2020 - 2024 MY Camry [03/2020 -        ]; A25A-FKS (FUEL): FUEL SYSTEM: PRECAUTION

NOTICE:

When disconnecting the fuel tube connector, do not excessively pull on the fuel return vent tube sub-assembly.

(c) Remove the fuel suction tube set gasket from the fuel tank assembly.

6. REMOVE NO. 2 FUEL SENDER GAUGE ASSEMBLY

(a) Disconnect the No. 2 fuel sender gauge assembly connector.

(b) Disengage the 2 clamps to disconnect the wire harness from the rear fuel main and return tube sub-assembly.

NOTICE:

  • Do not damage the wire harness.
  • When disengaging each wire harness from the clamp, disengage one wire at a time.

(c) Disengage the claw to remove the No. 2 fuel sender gauge assembly from the rear fuel main and return tube sub-assembly.

NOTICE:

Be careful not to bend the arm of the No. 2 fuel sender gauge assembly.