METER / GAUGE / DISPLAY: METER / GAUGE SYSTEM: B150013,B150113; Fuel Sender Circuit Open; 2020 - 2024 MY Camry [03/2020

Last Modified: 11-20-2023	6.11:8.1.0	Doc ID: RM100000001MUDW
Model Year Start: 2020	Model: Camry	Prod Date Range: [03/2020 - ]
Title: METER / GAUGE / DISPLAY: METER / GAUGE SYSTEM: B150013,B150113; Fuel Sender Circuit Open; 2020 - 2024 MY Camry [03/2020 - ]

DTC

B150013

Fuel Sender Circuit Open

DTC

B150113

Sub Fuel Sender Circuit Open

DESCRIPTION

FOR 2WD

The fuel sender gauge assembly is connected to the combination meter assembly via direct line. If there is an open or short in the direct line, the combination meter assembly stores DTC B150013.

FOR AWD

The fuel sender gauge assembly and No. 2 fuel sender gauge assembly are connected to the combination meter assembly via direct line. If there is an open or short in the direct line, the combination meter assembly stores DTC B150013 or B150113.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Memory

Note

B150013

Fuel Sender Circuit Open

Diagnosis Condition:

The ignition switch is ON
IG power source voltage is 9.5 V or more

Malfunction Status:

Voltage signal from fuel sender gauge assembly is 0.2 V or less
Voltage signal from fuel sender gauge assembly is 4.7 V or more

Malfunction Time:

10 seconds or more

Harness or connector
Fuel sender gauge assembly
Fuel suction tube with pump and gauge assembly
Combination meter assembly

DTC stored

B150113

Sub Fuel Sender Circuit Open

Diagnosis Condition:

The ignition switch is ON
IG power source voltage is 9.5 V or more

Malfunction Status:

Voltage signal from No. 2 fuel sender gauge assembly is 0.2 V or less
Voltage signal from No. 2 fuel sender gauge assembly is 4.7 V or more

Malfunction Time:

10 seconds or more

Harness or connector
No. 2 fuel sender gauge assembly
Rear fuel main and return tube sub-assembly
Combination meter assembly

DTC stored

for AWD

WIRING DIAGRAM

FOR 2WD

FOR AWD

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

PROCEDURE

1.	CHECK FOR DTC (METER / GAUGE SYSTEM)

(a) Check for DTCs.

Body Electrical > Combination Meter > Trouble Codes

Result	Proceed to
Only DTC B150013 is output	A
Only DTC B150113 is output	B
DTC B150013 and B150113 are output at the same time	C

GO TO STEP 11

GO TO STEP 15

2.	CONFIRM MODEL

(a) Choose the model to be inspected.

Result	Proceed to
for 2WD	A
for AWD	B

GO TO STEP 7

3.	READ VALUE USING TECHSTREAM

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(d) Enter the following menus: Body Electrical / Combination Meter / Data List.

(e) Read the Data List according to the display on the Techstream.

Body Electrical > Combination Meter > Data List

Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
Fuel Input	Fuel level input	Min.: 0 L, Max.: 655.34 L	for 60 Liters (63.4 US qts, 52.8 Imp. qts) Total Tank Capacity Type: Fuel receiver gauge indicates F: 54.2 L Fuel receiver gauge indicates 3/4: 45.5 L Fuel receiver gauge indicates 1/2: 30.3 L Fuel receiver gauge indicates 1/4: 15.2 L Fuel receiver gauge indicates E: 6.1 L for 55 Liters (for 58.1 US qts, 48.4 Imp. qts) Total Tank Capacity Type: Fuel receiver gauge indicates F: 48.1 L Fuel receiver gauge indicates 3/4: 41.3 L Fuel receiver gauge indicates 1/2: 27.5 L Fuel receiver gauge indicates 1/4: 13.8 L Fuel receiver gauge indicates E: 5.5 L	The detected value of the fuel sender gauge assembly is displayed.

Body Electrical > Combination Meter > Data List

Tester Display
Fuel Input

Result	Proceed to
Fuel level data can be displayed on the Techstream	A
Fuel level data cannot be displayed on the Techstream	B

REPLACE COMBINATION METER ASSEMBLY

4.	CHECK HARNESS AND CONNECTOR (FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY - COMBINATION METER ASSEMBLY)

(a) Disconnect the R44 fuel suction tube with pump and gauge assembly connector.

(b) Disconnect the K21 combination meter assembly connector.

Standard Resistance:

Tester Connection	Condition	Specified Condition
R44-1 (FV) - K21-15 (FV)	Always	Below 1 Ω
R44-2 (FE) - K21-33 (FE)	Always	Below 1 Ω
R44-3 (FS) - K21-14 (FR)	Always	Below 1 Ω
R44-1 (FV) or K21-15 (FV) - Body ground	Always	10 kΩ or higher
R44-3 (FS) or K21-14 (FR) - Body ground	Always	10 kΩ or higher

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.	INSPECT FUEL SENDER GAUGE ASSEMBLY

(a) Remove the fuel sender gauge assembly.

for 2GR-FKS: Click here

for A25A-FKS: Click here

(b) Inspect the fuel sender gauge assembly.

for 2GR-FKS: Click here

for A25A-FKS: Click here

REPLACE FUEL SENDER GAUGE ASSEMBLY

for 2GR-FKS: Click here

for A25A-FKS: Click here

6.	INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

*a	Component without harness connected (Fuel Suction Tube with Pump and Gauge Assembly)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
R44-1 (FV) - A-3	Always	Below 1 Ω
R44-2 (FE) - A-2	Always	Below 1 Ω
R44-3 (FS) - A-1	Always	Below 1 Ω
R44-1 (FV) - R44-3 (FS) or A-3 - A-1	Always	10 kΩ or higher
R44-1 (FV) - R44-2 (FE) or A-3 - A-2	Always	10 kΩ or higher
R44-2 (FE) - R44-3 (FS) or A-2 - A-1	Always	10 kΩ or higher

REPLACE COMBINATION METER ASSEMBLY

REPLACE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

for 2GR-FKS: Click here

for A25A-FKS: Click here

7.	READ VALUE USING TECHSTREAM

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(d) Enter the following menus: Body Electrical / Combination Meter / Data List.

(e) Read the Data List according to the display on the Techstream.

Body Electrical > Combination Meter > Data List

Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
Fuel Input	Fuel level input	Min.: 0 L, Max.: 655.34 L	Fuel receiver gauge indicates F: 49.5 L* Fuel receiver gauge indicates 3/4: 41.3 L* Fuel receiver gauge indicates 1/2: 27.5 L* Fuel receiver gauge indicates 1/4: 13.8 L* Fuel receiver gauge indicates E: 5.5 L*	The detected value of the fuel sender gauge assembly is displayed.

*: Combined value of "Fuel Input" and "Sub Fuel Input"

Body Electrical > Combination Meter > Data List

Tester Display
Fuel Input

Result	Proceed to
Fuel level data can be displayed on the Techstream	A
Fuel level data cannot be displayed on the Techstream	B

REPLACE COMBINATION METER ASSEMBLY

8.	CHECK HARNESS AND CONNECTOR (FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY - COMBINATION METER ASSEMBLY)

(a) Disconnect the R44 fuel suction tube with pump and gauge assembly connector.

(b) Disconnect the K21 combination meter assembly connector.

Standard Resistance:

Tester Connection	Condition	Specified Condition
R44-1 (FV) - K21-15 (FV)	Always	Below 1 Ω
R44-2 (FE) - K21-33 (FE)	Always	Below 1 Ω
R44-3 (FS) - K21-14 (FR)	Always	Below 1 Ω
R44-3 (FS) or K21-14 (FR) - Body ground	Always	10 kΩ or higher

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.	INSPECT FUEL SENDER GAUGE ASSEMBLY

(a) Remove the fuel sender gauge assembly.

Click here

(b) Inspect the fuel sender gauge assembly.

Click here

REPLACE FUEL SENDER GAUGE ASSEMBLY

10.	INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

*a	Component without harness connected (Fuel Suction Tube with Pump and Gauge Assembly)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
R44-1 (FV) - A-3	Always	Below 1 Ω
R44-2 (FE) - A-2	Always	Below 1 Ω
R44-3 (FS) - A-1	Always	Below 1 Ω
R44-1 (FV) - R44-3 (FS) or A-3 - A-1	Always	10 kΩ or higher
R44-1 (FV) - R44-2 (FE) or A-3 - A-2	Always	10 kΩ or higher
R44-2 (FE) - R44-3 (FS) or A-2 - A-1	Always	10 kΩ or higher

REPLACE COMBINATION METER ASSEMBLY

REPLACE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

11.	READ VALUE USING TECHSTREAM

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(d) Enter the following menus: Body Electrical / Combination Meter / Data List.

(e) Read the Data List according to the display on the Techstream.

Body Electrical > Combination Meter > Data List

Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
Sub Fuel Input	Fuel level input	Min.: 0 L, Max.: 655.34 L or Unset	Fuel receiver gauge indicates F: 49.5 L* Fuel receiver gauge indicates 3/4: 41.3 L* Fuel receiver gauge indicates 1/2: 27.5 L* Fuel receiver gauge indicates 1/4: 13.8 L* Fuel receiver gauge indicates E: 5.5 L*	The detected value of the No. 2 fuel sender gauge assembly is displayed.

*: Combined value of "Fuel Input" and "Sub Fuel Input"

Body Electrical > Combination Meter > Data List

Tester Display
Sub Fuel Input

Result	Proceed to
Fuel level data can be displayed on the Techstream	A
Fuel level data cannot be displayed on the Techstream	B

REPLACE COMBINATION METER ASSEMBLY

12.	CHECK HARNESS AND CONNECTOR (REAR FUEL MAIN AND RETURN TUBE SUB-ASSEMBLY - COMBINATION METER ASSEMBLY)

(a) Disconnect the R124 rear fuel main and return tube sub-assembly connector.

(b) Disconnect the K21 combination meter assembly connector.

Standard Resistance:

Tester Connection	Condition	Specified Condition
R124-1 (FV) - K21-15 (FV)	Always	Below 1 Ω
R124-2 (FE) - K21-33 (FE)	Always	Below 1 Ω
R124-3 (FR) - K21-35 (FR2)	Always	Below 1 Ω
R124-3 (FR) or K21-35 (FR2) - Body ground	Always	10 kΩ or higher

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.	INSPECT NO. 2 FUEL SENDER GAUGE ASSEMBLY

(a) Remove the No. 2 fuel sender gauge assembly.

Click here

(b) Inspect the No. 2 fuel sender gauge assembly.

Click here

REPLACE NO. 2 FUEL SENDER GAUGE ASSEMBLY

14.	INSPECT REAR FUEL MAIN AND RETURN TUBE SUB-ASSEMBLY

*a	Component without harness connected (Rear Fuel Main and Return Tube Sub-assembly)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
R124-1 (FV) - B-3	Always	Below 1 Ω
R124-2 (FE) - B-2	Always	Below 1 Ω
R124-3 (FR) - B-1	Always	Below 1 Ω
R124-1 (FV) - R124-3 (FR) or B-3 - B-1	Always	10 kΩ or higher
R124-1(FV) - R124-2(FE) or B-3 - B-2	Always	10 kΩ or higher
R124-2(FE) - R124-3(FR) or B-2 - B-1	Always	10 kΩ or higher

REPLACE COMBINATION METER ASSEMBLY

REPLACE REAR FUEL MAIN AND RETURN TUBE SUB-ASSEMBLY

15.	READ VALUE USING TECHSTREAM

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(d) Enter the following menus: Body Electrical / Combination Meter / Data List.

(e) Read the Data List according to the display on the Techstream.

Body Electrical > Combination Meter > Data List

Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
Fuel Input	Fuel level input	Min.: 0 L, Max.: 655.34 L or Unset	Fuel receiver gauge indicates F: 49.5 L* Fuel receiver gauge indicates 3/4: 41.3 L* Fuel receiver gauge indicates 1/2: 27.5 L* Fuel receiver gauge indicates 1/4: 13.8 L* Fuel receiver gauge indicates E: 5.5 L*	The detected value of the fuel sender gauge assembly is displayed.
Sub Fuel Input	Fuel level input	Min.: 0 L, Max.: 655.34 L or Unset	Fuel receiver gauge indicates F: 49.5 L* Fuel receiver gauge indicates 3/4: 41.3 L* Fuel receiver gauge indicates 1/2: 27.5 L* Fuel receiver gauge indicates 1/4: 13.8 L* Fuel receiver gauge indicates E: 5.5 L*	The detected value of the No. 2 fuel sender gauge assembly is displayed.

*: Combined value of "Fuel Input" and "Sub Fuel Input"

Body Electrical > Combination Meter > Data List

Tester Display
Fuel Input
Sub Fuel Input

Result	Proceed to
Fuel level data can be displayed on the Techstream	A
Fuel level data cannot be displayed on the Techstream	B

REPLACE COMBINATION METER ASSEMBLY

16.	CHECK HARNESS AND CONNECTOR (FUEL SENDER GAUGE SIDE - COMBINATION METER ASSEMBLY)

(a) Disconnect the R44 fuel suction tube with pump and gauge assembly connector.

(b) Disconnect the R124 rear fuel main and return tube sub-assembly connector.

(d) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
R44-1 (FV) - K21-15 (FV)	Always	Below 1 Ω
R44-2 (FE) - K21-33 (FE)	Always	Below 1 Ω
R124-1 (FV) - K21-15 (FV)	Always	Below 1 Ω
R124-2 (FE) - K21-33 (FE)	Always	Below 1 Ω
R44-1 (FV), R124-1 (FV) or K21-15 (FV) - Body ground	Always	10 kΩ or higher
R44-3 (FS) or K21-14 (FR) - Body ground	Always	10 kΩ or higher
R124-3 (FR) or K21-35 (FR2) - Body ground	Always	10 kΩ or higher

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.	INSPECT FUEL SENDER GAUGE ASSEMBLY

(a) Remove the fuel sender gauge assembly.

Click here

(b) Inspect the fuel sender gauge assembly.

Click here

REPLACE FUEL SENDER GAUGE ASSEMBLY

18.	INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

*a	Component without harness connected (Fuel Suction Tube with Pump and Gauge Assembly)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

R44-1 (FV) - R44-3 (FS)

A-3 - A-1

Always

10 kΩ or higher

R44-1 (FV) - R44-2 (FE)

A-3 - A-2

Always

10 kΩ or higher

R44-2 (FE) - R44-3 (FS)

A-2 - A-1

Always

10 kΩ or higher

REPLACE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

19.	INSPECT NO. 2 FUEL SENDER GAUGE ASSEMBLY

(a) Remove the No. 2 fuel sender gauge assembly.

Click here

(b) Inspect the No. 2 fuel sender gauge assembly.

Click here

REPLACE NO. 2 FUEL SENDER GAUGE ASSEMBLY

20.	INSPECT REAR FUEL MAIN AND RETURN TUBE SUB-ASSEMBLY

*a	Component without harness connected (Rear Fuel Main and Return Tube Sub-assembly)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

R124-1 (FV) - R124-3 (FR)

B-3 - B-1

Always

10 kΩ or higher

R124-1 (FV) - R124-2 (FE)

B-3 - B-2

Always

10 kΩ or higher

R124-2 (FE) - R124-3 (FR)

B-2 - B-1

Always

10 kΩ or higher

REPLACE COMBINATION METER ASSEMBLY

REPLACE REAR FUEL MAIN AND RETURN TUBE SUB-ASSEMBLY

DESCRIPTION

WIRING DIAGRAM

CAUTION / NOTICE / HINT

PROCEDURE

Body Electrical > Combination Meter > Trouble Codes

Body Electrical > Combination Meter > Data List

for 60 Liters (63.4 US qts, 52.8 Imp. qts) Total Tank Capacity Type:

for 55 Liters (for 58.1 US qts, 48.4 Imp. qts) Total Tank Capacity Type:

Body Electrical > Combination Meter > Data List

Body Electrical > Combination Meter > Data List

Body Electrical > Combination Meter > Data List

Body Electrical > Combination Meter > Data List

Body Electrical > Combination Meter > Data List

Body Electrical > Combination Meter > Data List

Body Electrical > Combination Meter > Data List