Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM100000001MFRY
Model Year Start: 2020 Model: Camry Prod Date Range: [03/2020 -           ]
Title: UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: U010087; Lost Communication with ECM/PCM "A" Missing Message; 2020 - 2024 MY Camry [03/2020 -        ]

DTC

U010087

Lost Communication with ECM/PCM "A" Missing Message

DESCRIPTION

The engine control unit and transmission control unit are located inside the ECM. The engine control unit intercommunicates with the transmission control unit using CAN communication.

If there is a problem in this intercommunication, the ECM stores this DTC.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Memory

Note

U010087

Lost Communication with ECM/PCM "A" Missing Message

While the ignition switch is ON, there is no communication between the engine control unit and transmission control unit for 1.25 seconds or more (1-trip detection logic).

ECM

Comes on

DTC stored

SAE Code: U0100

MONITOR STRATEGY

Related DTCs

U0100: Verify communication

Required sensors/components (Main)

ECM

Required sensors/components (Related)

-

Frequency of Operation

Continuous

Duration

1.25 sec.

MIL Operation

Immediately

Sequence of Operation

None

TYPICAL ENABLING CONDITIONS

The monitor will run whenever the following DTCs are not stored

None

Battery Voltage

10.5 V or more

Ignition switch

ON

Starter

Off

TYPICAL MALFUNCTION THRESHOLDS

Communication signal

Lost communication with ECM/PCM

CONFIRMATION DRIVING PATTERN

HINT:

  • After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
  • When clearing the permanent DTCs, refer to the Clear Permanent DTC procedure.

    Click here 2020 - 2024 MY Camry [03/2020 -        ]; UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: DTC CHECK / CLEAR

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for 2 minutes or more.
  5. Turn the ignition switch to ON and turn the Techstream on.
  6. Wait for 3 seconds or more with the ignition switch ON. [*1]

    HINT:

    [*1] : Normal judgment procedure.

    The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.

  7. Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
  8. Input the DTC: U010087.
  9. Check the DTC judgment result.

    Techstream Display

    Description

    NORMAL

    • DTC judgment completed
    • System normal

    ABNORMAL

    • DTC judgment completed
    • System abnormal

    INCOMPLETE

    • DTC judgment not completed
    • Perform driving pattern after confirming DTC enabling conditions

    N/A

    • Unable to perform DTC judgment
    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:

    • If the judgment result shows NORMAL, the system is normal.
    • If the judgment result shows ABNORMAL, the system has a malfunction.
    • If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.

CAUTION / NOTICE / HINT

NOTICE:

  • Perform the universal trip to clear permanent DTCs.

    Click here 2020 - 2024 MY Camry [03/2020 -        ]; UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: DTC CHECK / CLEAR

  • Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

    Click here 2020 MY Camry [03/2020 - 10/2020]; UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: PRECAUTION 2021 - 2024 MY Camry [10/2020 -        ]; UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: PRECAUTION

PROCEDURE

1.

CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC U010087)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Powertrain / Transmission / Trouble Codes.

Powertrain > Transmission > Trouble Codes

(e) Read the DTCs using the Techstream.

Result

Proceed to

Only DTC U010087 is output

A

DTC U010087 and other DTCs are output

B

B

GO TO DTC CHART 2020 MY Camry [03/2020 - 10/2020]; UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: DIAGNOSTIC TROUBLE CODE CHART 2021 - 2024 MY Camry [10/2020 -        ]; UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: DIAGNOSTIC TROUBLE CODE CHART

A

2.

REPLACE ECM

(a) Replace the ECM.

Click here 2020 MY Camry [03/2020 - 10/2020]; A25A-FKS (ENGINE CONTROL): ECM: REMOVAL 2021 - 2022 MY Camry [10/2020 - 08/2022]; A25A-FKS (ENGINE CONTROL): ECM: REMOVAL 2023 - 2024 MY Camry [08/2022 -        ]; A25A-FKS (ENGINE CONTROL): ECM: REMOVAL

NEXT

PERFORM REGISTRATION