Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM100000001MFRI
Model Year Start: 2020 Model: Camry Prod Date Range: [03/2020 -           ]
Title: UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: P271314; Pressure Control Solenoid "D" Circuit Short to Ground or Open; 2020 - 2024 MY Camry [03/2020 -        ]

DTC

P271314

Pressure Control Solenoid "D" Circuit Short to Ground or Open

DESCRIPTION

Refer to DTC P27137F.

Click here 2020 - 2024 MY Camry [03/2020 -        ]; UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: P27137F; Pressure Control Solenoid "D" Actuator Stuck Off

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Memory

Note

P271314

Pressure Control Solenoid "D" Circuit Short to Ground or Open

While the engine is running, a short to ground or open is detected in the solenoid (SLT) valve circuit for 1 second (1-trip detection logic).

  • Solenoid (SLT) valve
  • Transmission wire
  • Harness and connector
  • ECM

Comes on

DTC stored

SAE Code:

P2720

MONITOR DESCRIPTION

When an open or short to ground in the solenoid (SLT) valve circuit is detected, the ECM will determine that there is a malfunction, illuminate the MIL and store this DTC.

MONITOR STRATEGY

Related DTC

P2720: Solenoid (SLT) valve/Range check (Low current)

Required sensors/components

Solenoid (SLT) valve

Frequency of operation

Continuous

Duration

Condition (a): 1 sec.

Condition (b): 1.1 sec.

MIL operation

Immediate

Sequence of operation

None

TYPICAL ENABLING CONDITIONS

The monitor will run whenever the following DTCs are not stored

None

Solenoid current cut status

Not cut

Ignition switch

ON

Starter

OFF

Battery voltage

10.5 V or more

Target current (0.1 sec. or more)

0.2 A or more

TYPICAL MALFUNCTION THRESHOLDS

Any of the following conditions are met

(a) or (b)

(a) Solenoid current

Less than 0.075 A

(b) Solenoid high current cutout by solenoid driver IC

ON

COMPONENT OPERATING RANGE

Solenoid current

0.075 A or more

Solenoid high current cutout by solenoid driver IC

OFF

CONFIRMATION DRIVING PATTERN

HINT:

  • After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
  • When clearing the permanent DTCs, refer to the Clear Permanent DTC procedure.

    Click here 2020 - 2024 MY Camry [03/2020 -        ]; UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: DTC CHECK / CLEAR

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  4. Turn the ignition switch off and wait for 2 minutes or more.
  5. Turn the ignition switch to ON and turn the Techstream on.
  6. Start the engine.
  7. Wait for 2 seconds or more with the engine running. [*1]

    HINT:

    [*1] : Normal judgment procedure.

    The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.

  8. Enter the following menus: Powertrain / Transmission / Utility / All Readiness.
  9. Input the DTC: P271314.
  10. Check the DTC judgment result.

    Techstream Display

    Description

    NORMAL

    • DTC judgment completed
    • System normal

    ABNORMAL

    • DTC judgment completed
    • System abnormal

    INCOMPLETE

    • DTC judgment not completed
    • Perform driving pattern after confirming DTC enabling conditions

    N/A

    • Unable to perform DTC judgment
    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:

    • If the judgment result shows NORMAL, the system is normal.
    • If the judgment result shows ABNORMAL, the system has a malfunction.
    • If the judgment result shows INCOMPLETE or N/A, perform the normal judgment procedure again.

WIRING DIAGRAM

Refer to DTC P271312.

Click here 2020 - 2024 MY Camry [03/2020 -        ]; UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: P271312; Pressure Control Solenoid "D" Circuit Short to Battery

CAUTION / NOTICE / HINT

NOTICE:

  • Perform the universal trip to clear permanent DTCs.

    Click here 2020 - 2024 MY Camry [03/2020 -        ]; UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: DTC CHECK / CLEAR

  • Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

    Click here 2020 MY Camry [03/2020 - 10/2020]; UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: PRECAUTION 2021 - 2024 MY Camry [10/2020 -        ]; UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: PRECAUTION

PROCEDURE

1.

CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE (SOLENOID (SLT) VALVE) - ECM)

(a) Disconnect the C101 ECM connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

C101-10 (SLT+) - C101-9 (SLT-)

20°C (68°F)

5.0 to 5.6 Ω

C101-10 (SLT+) or C101-9 (SLT-) - Body ground and other terminals

Always

10 kΩ or higher

NG

GO TO STEP 3

OK

2.

REPLACE ECM

(a) Replace the ECM.

Click here 2020 MY Camry [03/2020 - 10/2020]; A25A-FKS (ENGINE CONTROL): ECM: REMOVAL 2021 - 2022 MY Camry [10/2020 - 08/2022]; A25A-FKS (ENGINE CONTROL): ECM: REMOVAL 2023 - 2024 MY Camry [08/2022 -        ]; A25A-FKS (ENGINE CONTROL): ECM: REMOVAL

NEXT

PERFORM REGISTRATION

3.

CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

(a) Disconnect the C92 transmission wire connector.

(b) Disconnect the C101 ECM connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

C92-24 (SLT+) - C101-10 (SLT+)

Always

Below 1 Ω

C92-23 (SLT-) - C101-9 (SLT-)

Always

Below 1 Ω

C92-24 (SLT+) or C101-10 (SLT+) - Body ground and other terminals

Always

10 kΩ or higher

C92-23 (SLT-) or C101-9 (SLT-) - Body ground and other terminals

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM)

OK

4.

INSPECT SOLENOID (SLT) VALVE

(a) Remove the solenoid (SLT) valve.

Click here 2020 - 2024 MY Camry [03/2020 -        ]; UB80F (AUTOMATIC TRANSMISSION / TRANSAXLE): VALVE BODY ASSEMBLY: DISASSEMBLY

*a

Component without harness connected

(Solenoid (SLT) Valve)

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

Solenoid (SLT) valve connector terminal 1 - terminal 2

20°C (68°F)

5.0 to 5.6 Ω

(c) Connect a positive (+) lead from the battery with a 21 W bulb to terminal 1 and a negative (-) lead to terminal 2 of the solenoid valve connector. Check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.

OK

REPAIR OR REPLACE TRANSMISSION WIRE

NG

REPLACE SOLENOID (SLT) VALVE