Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM100000001L9B3
Model Year Start: 2020 Model: Camry Prod Date Range: [09/2019 - 10/2020]
Title: EXTERIOR PANELS / TRIM: FRONT DOOR BELT MOULDING: REMOVAL; 2020 MY Camry [09/2019 - 10/2020]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front door belt moulding removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

*: When performing learning using the Techstream.

Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; PARK ASSIST / MONITORING: INTELLIGENT CLEARANCE SONAR SYSTEM: CALIBRATION

Disconnect cable from negative battery terminal

Perform steering sensor zero point calibration

Lane departure alert system (w/ Steering Control)

2018 - 2020 MY Camry [03/2017 - 10/2020]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Pre-collision system

Intelligent clearance sonar system*

Memorize steering angle neutral point

Parking assist monitor system

2018 - 2024 MY Camry [03/2017 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION

Panoramic view monitor system

2018 - 2020 MY Camry [06/2017 - 10/2020]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: INITIALIZATION

Front door glass sub-assembly

Initialize power window control system

  • Auto up and down function
  • Jam protection function
  • Remote control function
  • Key-linked function
  • Wireless transmitter-linked function
  • Key-off operation function
  • Catch protection function
  • Window open warning function

2018 - 2024 MY Camry [03/2017 -        ]; WINDOW / GLASS: POWER WINDOW CONTROL SYSTEM: INITIALIZATION

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here 2020 MY Camry [09/2019 - 03/2020]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION 2020 - 2024 MY Camry [03/2020 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

for A25A-FKS:

Click here 2019 - 2020 MY Camry [08/2018 - 10/2020]; MAINTENANCE: A25A-FKS BATTERY: REMOVAL+

for 2GR-FKS:

Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; MAINTENANCE: 2GR-FKS BATTERY: REMOVAL+

3. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH

Click here 2020 MY Camry [09/2019 - 10/2020]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+

4. REMOVE FRONT DOOR ARMREST COVER SUB-ASSEMBLY

Click here 2020 MY Camry [09/2019 - 10/2020]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+

5. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)

Click here 2020 MY Camry [09/2019 - 10/2020]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+

6. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)

Click here 2020 MY Camry [09/2019 - 10/2020]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+

7. REMOVE FRONT ARMREST ASSEMBLY

Click here 2020 MY Camry [09/2019 - 10/2020]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+

8. REMOVE FRONT DOOR TRIM PLATE (w/o Courtesy Light)

Click here 2020 MY Camry [09/2019 - 10/2020]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+

9. REMOVE COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)

Click here 2018 - 2024 MY Camry [03/2017 -        ]; LIGHTING (INT): DOOR COURTESY LIGHT: REMOVAL+

10. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

Click here 2020 MY Camry [09/2019 - 10/2020]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+

11. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP WITH FRONT DOOR VENT SEAL

Click here 2020 MY Camry [09/2019 - 10/2020]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+

12. REMOVE FRONT DOOR SERVICE HOLE COVER

Click here 2020 MY Camry [09/2019 - 10/2020]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+

13. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

Click here 2020 MY Camry [09/2019 - 10/2020]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+

14. REMOVE FRONT DOOR BELT MOULDING ASSEMBLY

(a) Apply protective tape around the front door belt moulding assembly as shown in the illustration.

Protective Tape

(b) Disengage the 5 claws as shown in the illustration.

*a

Claw

Rotate in this Direction

(c) Using a thin-bladed screwdriver with its tip wrapped with protective tape, disengage the claw as shown in the illustration.

*a

Thin-bladed Screwdriver with its Tip Wrapped with Protective Tape

Push in this Direction

(d) Slightly twist and hold the front door belt moulding assembly in the direction indicated by the arrow (1) shown in the illustration.

Twist in this Direction (1)

Slide in this Direction (2)

NOTICE:

If the front door belt moulding assembly is pulled upwards, the claw may break and fall inside the door panel.

(e) Slide the front door belt moulding assembly in the direction indicated by the arrow (2) shown in the illustration to disengage the claw and remove the front door belt moulding assembly.