Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM100000001L8SN
Model Year Start: 2020 Model: Camry Prod Date Range: [09/2019 - 10/2020]
Title: SEAT BELT: REAR SEAT OUTER BELT ASSEMBLY: REMOVAL; 2020 MY Camry [09/2019 - 10/2020]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear seat outer belt assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link
*: When performing learning using the Techstream.

Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; PARK ASSIST / MONITORING: INTELLIGENT CLEARANCE SONAR SYSTEM: CALIBRATION

Disconnect cable from negative battery terminal

Perform steering sensor zero point calibration

Lane departure alert system (w/ Steering Control)

2018 - 2020 MY Camry [03/2017 - 10/2020]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Pre-collision system

Intelligent clearance sonar system*

Memorize steering angle neutral point

Parking assist monitor system

2018 - 2024 MY Camry [03/2017 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION

Panoramic view monitor system

2018 - 2020 MY Camry [06/2017 - 10/2020]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: INITIALIZATION

CAUTION:

  • Be sure to read Precaution thoroughly before servicing.

    Click here 2020 MY Camry [09/2019 - 03/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: PRECAUTION 2020 MY Camry [03/2020 - 10/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: PRECAUTION

  • Wear protective gloves. Sharp areas on the parts may injure your hands.

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here 2020 MY Camry [09/2019 - 03/2020]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION 2020 - 2024 MY Camry [03/2020 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

for A25A-FKS:

Click here 2019 - 2020 MY Camry [08/2018 - 10/2020]; MAINTENANCE: A25A-FKS BATTERY: REMOVAL+

for 2GR-FKS:

Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; MAINTENANCE: 2GR-FKS BATTERY: REMOVAL+

CAUTION:

  • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
  • If an airbag deploys for any reason, it may cause a serious injury.

3. REMOVE REAR SEAT ASSEMBLY (for Fixed Seat Type)

Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; SEAT: REAR SEAT ASSEMBLY (for Fixed Seat Type): REMOVAL

4. REMOVE REAR SEAT CUSHION ASSEMBLY (for Fold Down Seat Type)

Click here 2020 MY Camry [09/2019 - 10/2020]; SEAT: REAR SEAT ASSEMBLY (for Fold Down Seat Type): REMOVAL+

5. REMOVE REAR SEAT CUSHION LOCK HOOK (for Fold Down Seat Type)

Click here 2020 MY Camry [09/2019 - 10/2020]; SEAT: REAR SEAT ASSEMBLY (for Fold Down Seat Type): REMOVAL+

6. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH (for Fold Down Seat Type)

Click here 2020 MY Camry [09/2019 - 10/2020]; SEAT: REAR SEAT ASSEMBLY (for Fold Down Seat Type): REMOVAL+

7. REMOVE REAR SIDE SEATBACK ASSEMBLY LH (for Fold Down Seat Type)

Click here 2020 MY Camry [09/2019 - 10/2020]; SEAT: REAR SEAT ASSEMBLY (for Fold Down Seat Type): REMOVAL+

8. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH (for Fold Down Seat Type)

HINT:

Use the same procedure as for the LH side.

9. REMOVE REAR SIDE SEATBACK ASSEMBLY RH (for Fold Down Seat Type)

HINT:

Use the same procedure as for the LH side.

10. REMOVE INNER ROOF SIDE GARNISH LH

Click here 2020 MY Camry [09/2019 - 03/2020]; INTERIOR PANELS / TRIM: ROOF HEADLINING: REMOVAL+ 2020 MY Camry [03/2020 - 10/2020]; INTERIOR PANELS / TRIM: ROOF HEADLINING: REMOVAL+

11. REMOVE INNER ROOF SIDE GARNISH RH

HINT:

Use the same procedure as for the LH side.

12. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY LH

(a) Remove the bolt to disconnect the floor anchor of the rear seat outer belt assembly LH.

13. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

14. REMOVE CENTER STOP LIGHT SET

Click here 2018 - 2024 MY Camry [03/2017 -        ]; LIGHTING (EXT): HIGH MOUNTED STOP LIGHT ASSEMBLY: REMOVAL

15. REMOVE REAR SEAT SHOULDER BELT HOLE COVER

(a) Disengage the 2 claws and 2 guides to remove the rear seat shoulder belt hole cover.

HINT:

Use the same procedure for the other rear seat shoulder belt hole covers.

16. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY

(a) Fold the rear seatback assembly LH and rear seatback assembly RH forward.

(b) Remove the 2 clips.

(c) Disengage the 3 clips and 5 guides.

(d) Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly then remove the package tray trim panel assembly.

17. REMOVE REAR SEAT OUTER BELT ASSEMBLY LH

(a) Using a screwdriver, pull out the locking button as shown in the illustration to release the lock and disconnect the pretensioner connector.

HINT:

Tape the screwdriver tip before use.

*a

Protective Tape

*b

Locking Button

*c

Release

(b) Remove the 2 bolts.

(c) Disengage the guide to remove the rear seat outer belt assembly LH.

18. REMOVE REAR SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

19. REMOVE REAR SEAT BELT RETRACTOR COVER

(a) Remove the rear seat belt retractor cover as shown in the illustration.

HINT:

Use the same procedure for the RH side and LH side.

Remove in this Direction