Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM100000001KY7Y
Model Year Start: 2020 Model: Camry Prod Date Range: [09/2019 -           ]
Title: LIGHTING (EXT): LIGHTING SYSTEM: LO-beam Headlight does not Illuminate; 2020 - 2024 MY Camry [09/2019 -        ]

LO-beam Headlight does not Illuminate

DESCRIPTION

The main body ECU (multiplex network body ECU) controls the low beam headlights.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • Inspect the fuses for circuits related to this system before performing the following procedure.
  • Before replacing the main body ECU (multiplex network body ECU), refer to Registration.*

    Click here 2020 - 2022 MY Camry [09/2019 - 08/2022]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): REGISTRATION 2023 - 2024 MY Camry [08/2022 -        ]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): REGISTRATION

    • *: w/ Smart Key System

PROCEDURE

1.

PERFORM ACTIVE TEST USING TECHSTREAM

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Main Body / Active Test.

(e) Perform the Active Test according to the display on the Techstream.

Body Electrical > Main Body > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Headlight Relay

Low beam headlights

OFF or ON

-

Body Electrical > Main Body > Active Test

Tester Display

Headlight Relay

OK:

Low beam headlights illuminate.

Result

Proceed to

OK

A

NG (for LH Side)

B

NG (for RH Side)

C

A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE 2020 MY Camry [09/2019 - 03/2020]; LIGHTING (EXT): LIGHTING SYSTEM: PROBLEM SYMPTOMS TABLE 2020 MY Camry [03/2020 - 10/2020]; LIGHTING (EXT): LIGHTING SYSTEM: PROBLEM SYMPTOMS TABLE 2021 MY Camry [10/2020 - 08/2021]; LIGHTING (EXT): LIGHTING SYSTEM: PROBLEM SYMPTOMS TABLE 2022 - 2024 MY Camry [08/2021 -        ]; LIGHTING (EXT): LIGHTING SYSTEM: PROBLEM SYMPTOMS TABLE

C

GO TO STEP 9

B

2.

INSPECT HEADLIGHT ASSEMBLY LH (LO TERMINAL VOLTAGE)

*A

for Bulb Type Turn Signal Light

*B

for LED Type Turn Signal Light

*a

Front view of wire harness connector

(to Headlight Assembly LH)

-

-

(a) Disconnect the A51*1 or A75*2 headlight assembly LH connector.

  • *1: for Bulb Type Turn Signal Light
  • *2: for LED Type Turn Signal Light

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

for Bulb Type Turn Signal Light

Tester Connection

Condition

Specified Condition

A51-3 (LO) - Body ground

Light control switch in head position

11 to 14 V

for LED Type Turn Signal Light

Tester Connection

Condition

Specified Condition

A75-4 (LO) - Body ground

Light control switch in head position

11 to 14 V

NG

GO TO STEP 4

OK

3.

CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY LH - BODY GROUND)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

for Bulb Type Turn Signal Light

Tester Connection

Condition

Specified Condition

A51-1 (E) - Body ground

Always

Below 1 Ω

for LED Type Turn Signal Light

Tester Connection

Condition

Specified Condition

A75-8 (E) - Body ground

Always

Below 1 Ω

OK

REPLACE HEADLIGHT ASSEMBLY LH 2018 - 2020 MY Camry [06/2017 - 10/2020]; LIGHTING (EXT): HEADLIGHT ASSEMBLY: REMOVAL 2021 - 2024 MY Camry [10/2020 -        ]; LIGHTING (EXT): HEADLIGHT ASSEMBLY: REMOVAL

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.

CHECK HARNESS AND CONNECTOR (H-LP LH RELAY - HEADLIGHT ASSEMBLY LH)

(a) Remove the H-LP LH relay.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

for Bulb Type Turn Signal Light

Tester Connection

Condition

Specified Condition

3 (H-LP LH relay) - A51-3 (LO)

Always

Below 1 Ω

3 (H-LP LH relay) or A51-3 (LO) - Body ground

Always

10 kΩ or higher

for LED Type Turn Signal Light

Tester Connection

Condition

Specified Condition

3 (H-LP LH relay) - A75-4 (LO)

Always

Below 1 Ω

3 (H-LP LH relay) or A75-4 (LO) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

5.

INSPECT H-LP LH RELAY

(a) Inspect the H-LP LH relay.

Click here 2018 - 2024 MY Camry [06/2017 -        ]; LIGHTING (EXT): RELAY: ON-VEHICLE INSPECTION

NG

REPLACE H-LP LH RELAY

OK

6.

CHECK HARNESS AND CONNECTOR (POWER SOURCE - H-LP LH RELAY)

(a) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

2 (H-LP LH relay) - Body ground

Always

11 to 14 V

5 (H-LP LH relay) - Body ground

Always

11 to 14 V

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

7.

CHECK HARNESS AND CONNECTOR (H-LP LH RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

(a) Disconnect the 3C instrument panel junction block assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

1 (H-LP LH relay) - 3C-31

Always

Below 1 Ω

1 (H-LP LH relay) or 3C-31 - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

8.

INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

*a

Component without harness connected

(Instrument Panel Junction Block Assembly)

-

-

(a) Remove the instrument panel junction block assembly.

Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL 2021 - 2024 MY Camry [10/2020 -        ]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL

(b) Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

3C-31 - MB-15 (HRLY)

Always

Below 1 Ω

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) 2018 - 2020 MY Camry [06/2017 - 10/2020]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL 2021 - 2024 MY Camry [10/2020 -        ]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY 2018 - 2020 MY Camry [06/2017 - 10/2020]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL 2021 - 2024 MY Camry [10/2020 -        ]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL

9.

INSPECT HEADLIGHT ASSEMBLY RH (LO TERMINAL VOLTAGE)

*A

for Bulb Type Turn Signal Light

*B

for LED Type Turn Signal Light

*a

Front view of wire harness connector

(to Headlight Assembly RH)

-

-

(a) Disconnect the A50*1 or A74*2 headlight assembly RH connector.

  • *1: for Bulb Type Turn Signal Light
  • *2: for LED Type Turn Signal Light

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

for Bulb Type Turn Signal Light

Tester Connection

Condition

Specified Condition

A50-3 (LO) - Body ground

Light control switch in head position

11 to 14 V

for LED Type Turn Signal Light

Tester Connection

Condition

Specified Condition

A74-4 (LO) - Body ground

Light control switch in head position

11 to 14 V

NG

GO TO STEP 11

OK

10.

CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY RH - BODY GROUND)

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

for Bulb Type Turn Signal Light

Tester Connection

Condition

Specified Condition

A50-1 (E) - Body ground

Always

Below 1 Ω

for LED Type Turn Signal Light

Tester Connection

Condition

Specified Condition

A74-8 (E) - Body ground

Always

Below 1 Ω

OK

REPLACE HEADLIGHT ASSEMBLY RH 2018 - 2020 MY Camry [06/2017 - 10/2020]; LIGHTING (EXT): HEADLIGHT ASSEMBLY: REMOVAL 2021 - 2024 MY Camry [10/2020 -        ]; LIGHTING (EXT): HEADLIGHT ASSEMBLY: REMOVAL

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.

CHECK HARNESS AND CONNECTOR (H-LP RH RELAY - HEADLIGHT ASSEMBLY RH)

(a) Remove the H-LP RH relay.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

for Bulb Type Turn Signal Light

Tester Connection

Condition

Specified Condition

3 (H-LP RH relay) - A50-3 (LO)

Always

Below 1 Ω

3 (H-LP RH relay) or A50-3 (LO) - Body ground

Always

10 kΩ or higher

for LED Type Turn Signal Light

Tester Connection

Condition

Specified Condition

3 (H-LP RH relay) - A74-4 (LO)

Always

Below 1 Ω

3 (H-LP RH relay) or A74-4 (LO) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

12.

INSPECT H-LP RH RELAY

(a) Inspect the H-LP RH relay.

Click here 2018 - 2024 MY Camry [06/2017 -        ]; LIGHTING (EXT): RELAY: ON-VEHICLE INSPECTION

NG

REPLACE H-LP RH RELAY

OK

13.

CHECK HARNESS AND CONNECTOR (POWER SOURCE - H-LP RH RELAY)

(a) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

2 (H-LP RH relay) - Body ground

Always

11 to 14 V

5 (H-LP RH relay) - Body ground

Always

11 to 14 V

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

14.

CHECK HARNESS AND CONNECTOR (H-LP RH RELAY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

(a) Disconnect the K52 main body ECU (multiplex network body ECU) connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

1 (H-LP RH relay) - K52-12 (HRY2)

Always

Below 1 Ω

1 (H-LP RH relay) or K52-12 (HRY2) - Body ground

Always

10 kΩ or higher

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) 2018 - 2020 MY Camry [06/2017 - 10/2020]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL 2021 - 2024 MY Camry [10/2020 -        ]; POWER DISTRIBUTION: MAIN BODY ECU: REMOVAL

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR