Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM100000001KTRV
Model Year Start: 2020 Model: Camry Prod Date Range: [09/2019 - 10/2020]
Title: TELEMATICS: TELEMATICS SYSTEM: Warning Notification Function Malfunction; 2020 MY Camry [09/2019 - 10/2020]

Warning Notification Function Malfunction

PROCEDURE

1.

CHECK PROBLEM SYMPTOM (WARNING NOTIFICATION FUNCTION)

(a) Check the problem symptom.

(1) Check the problem symptom of the warning notification function.

Result

Proceed to

The multi-display screen does not show a warning message even though a warning light turns on or the multi-information display indicates a warning.

A

The multi-display screen shows a warning message even though a warning light is not on and the multi-information display does not indicate a warning.

B

The multi-display screen shows a warning message different from the warning light or the multi-information display.

HINT:

  • The warning notification function sends information to the service center through communication.
  • Carefully confirm the conditions that caused the malfunction in order to determine if a temporary problem with the radio wave signal conditions caused the malfunction.
B

GO TO STEP 7

A

2.

INSPECT WARNING LIGHT

(a) Check if the indicated warning light or message is listed in the following table.

HINT:

Only messages listed in the table are included in the warning notification function.

Warning Name

Engine warning

Brake system warning

VSC warning

ABS warning

EPS warning

Charging system warning

Airbag warning

PCS warning

Cruise warning

Clearance sonar warning

Drive start control warning

Brake override system warning

Entry and start system warning

Automatic headlight beam level control system warning

Intelligent adaptive front-lighting system (AFS)

Automatic high beam warning

LED headlight warning

Dynamic torque control AWD system warning

Tire pressure system warning

Electric parking brake warning

Auto hold warning

BSM system warning

Lane departure alert system warning

Reverse control wiper warning

Advanced sonar system warning

Secondary collision brake system warning

Engine maintenance

Rear cross traffic alert system warning (RCTA)

Engine oil level warning

Brake fluid warning

Engine oil pressure warning

Tire pressure low warning

Washer fluid level warning

High coolant temperature warning

Maintenance

Result

Proceed to

Warning light or message is listed in the table.

A

Warning light or message is not listed in the table.

B

B

END

A

3.

CHECK CAN COMMUNICATION SYSTEM

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Bus Check.

(e) Check that all ECUs and sensors that use CAN communication are connected.

Click here 2020 MY Camry [09/2019 - 03/2020]; NETWORKING: CAN COMMUNICATION SYSTEM: DIAGNOSIS SYSTEM 2020 MY Camry [03/2020 - 10/2020]; NETWORKING: CAN COMMUNICATION SYSTEM: DIAGNOSIS SYSTEM

Result

Proceed to

There are no connection problems.

A

There is a connection problem.

B

B

GO TO CAN COMMUNICATION SYSTEM

A

4.

CHECK METER WARNING LIGHT

(a) Check that the warning light of the combination meter assembly illuminates and a message displays on the multi-information display when there is a malfunction, and do not when there is not a malfunction.

OK:

There are no problems with warning lights or warning messages.

HINT:

The warning notification function of the telematics system uses the warning notification signals sent and received by the meter/gauge system. Therefore, if the meter/gauge system is not operating normally, the warning notification function will not operate normally.

Result

Proceed to

OK (w/ Navigation System)

A

OK (w/o Navigation System)

B

NG

C

B

GO TO STEP 6

C

GO TO METER / GAUGE SYSTEM

A

5.

CHECK NAVIGATION SYSTEM

(a) Check if the navigation system is operating and functioning normally.

OK:

The navigation system is normal.

OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

GO TO NAVIGATION SYSTEM

6.

CHECK AUDIO AND VISUAL SYSTEM

(a) Check if the audio and visual system is operating and functioning normally.

OK:

The audio and visual system is normal.

OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

GO TO AUDIO AND VISUAL SYSTEM

7.

CHECK METER WARNING LIGHT

(a) Check that the warning light of the combination meter assembly illuminates and a message displays on the multi-information display when there is a malfunction, and do not when there is not a malfunction.

OK:

There are no problems with warning lights or warning messages.

HINT:

The warning notification function of the telematics system uses the warning notification signals sent and received by the meter/gauge system. Therefore, if the meter/gauge system is not operating normally, the warning notification function will not operate normally.

OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

GO TO METER / GAUGE SYSTEM