| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM100000001KEDW |
| Model Year Start: 2020 | Model: Camry | Prod Date Range: [09/2019 - ] |
| Title: AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: B15C3; Speaker Output Short; 2020 - 2024 MY Camry [09/2019 - ] | ||
|
DTC |
B15C3 |
Speaker Output Short |
DESCRIPTION
This DTC is stored when a malfunction occurs in the speakers.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
|---|---|---|---|
|
B15C3 |
Speaker Output Short |
A short is detected in the speaker output circuit |
|
-
*1: for 6 Speakers
*2: for 9 Speakers
*3: w/ Manual (SOS) Switch
WIRING DIAGRAM
for 6 Speakers
for 9 Speakers
CAUTION / NOTICE / HINT
NOTICE:
-
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.
Click here
![2018 - 2020 MY Camry [06/2017 - 10/2020]; AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: PRECAUTION](/t3Portal/stylegraphics/info.gif)
-
When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:
- A communication malfunction DTC may be stored.
- The radio and display receiver assembly may not operate normally.
-
Before replacing the DCM (telematics transceiver), refer to Registration.
Click here
PROCEDURE
|
1. |
CHECK MODEL |
(a) Choose the model to be inspected.
|
Result |
Proceed to |
|---|---|
|
for 6 Speakers (w/ Manual (SOS) Switch) |
A |
|
for 6 Speakers (w/o Manual (SOS) Switch) |
B |
|
for 9 Speakers (w/ Manual (SOS) Switch) |
C |
|
for 9 Speakers (w/o Manual (SOS) Switch) |
D |
| B |
|
| C |
|
| D |
|
|
|
2. |
CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY, DCM (TELEMATICS TRANSCEIVER) OR SPEAKERS - BODY GROUND) |
(a) Disconnect the K4 radio and display receiver assembly connector.
(b) Disconnect the K139 DCM (telematics transceiver) connector.
(c) Disconnect the K7 and K8 front No. 2 speaker assembly connectors.
(d) Disconnect the Q7 and P7 rear speaker assembly connectors.
(e) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
K4-1 (FR+) or K139-1 (SPI+) - Body ground |
Always |
10 kΩ or higher |
|
K4-6 (FR-) or K139-2 (SPI-) - Body ground |
Always |
10 kΩ or higher |
|
K4-2 (FL+) or K8-4 (TWL+) - Body ground |
Always |
10 kΩ or higher |
|
K4-7 (FL-) or K8-2 (TWL-) - Body ground |
Always |
10 kΩ or higher |
|
K4-4 (RR+) or P7-2 - Body ground |
Always |
10 kΩ or higher |
|
K4-9 (RR-) or P7-1 - Body ground |
Always |
10 kΩ or higher |
|
K4-3 (RL+) or Q7-2 - Body ground |
Always |
10 kΩ or higher |
|
K4-8 (RL-) or Q7-1 - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
3. |
CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) OR SPEAKER - BODY GROUND) |
(a) Disconnect the K139 DCM (telematics transceiver) connector.
(b) Disconnect the K7 front No. 2 speaker assembly RH connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
K139-3 (SPO+) or K7-4 (TWR+) - Body ground |
Always |
10 kΩ or higher |
|
K139-4 (SPO-) or K7-2 (TWR-) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
4. |
INSPECT DCM (TELEMATICS TRANSCEIVER) |
(a) Remove the DCM (telematics transceiver).
Click here
|
(b) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
| OK |
|
| NG |
|
REPLACE DCM (TELEMATICS TRANSCEIVER)
|
|
5. |
CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY OR SPEAKERS - BODY GROUND) |
(a) Disconnect the K4 radio and display receiver assembly connector.
(b) Disconnect the K7 and K8 front No. 2 speaker assembly connectors.
(c) Disconnect the Q7 and P7 rear speaker assembly connectors.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
K4-1 (FR+) or K7-4 (TWR+) - Body ground |
Always |
10 kΩ or higher |
|
K4-6 (FR-) or K7-2 (TWR-) - Body ground |
Always |
10 kΩ or higher |
|
K4-2 (FL+) or K8-4 (TWL+) - Body ground |
Always |
10 kΩ or higher |
|
K4-7 (FL-) or K8-2 (TWL-) - Body ground |
Always |
10 kΩ or higher |
|
K4-4 (RR+) or P7-2 - Body ground |
Always |
10 kΩ or higher |
|
K4-9 (RR-) or P7-1 - Body ground |
Always |
10 kΩ or higher |
|
K4-3 (RL+) or Q7-2 - Body ground |
Always |
10 kΩ or higher |
|
K4-8 (RL-) or Q7-1 - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
6. |
CHECK HARNESS AND CONNECTOR (FRONT NO. 1 SPEAKER ASSEMBLY OR FRONT NO. 2 SPEAKER ASSEMBLY - BODY GROUND) |
(a) Disconnect the N1 and O1 front No. 1 speaker assembly connectors.
(b) Disconnect the K7 and K8 front No. 2 speaker assembly connectors.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
N1-2 or K7-3 (+) - Body ground |
Always |
10 kΩ or higher |
|
N1-1 or K7-1 (-) - Body ground |
Always |
10 kΩ or higher |
|
O1-2 or K8-3 (+) - Body ground |
Always |
10 kΩ or higher |
|
O1-1 or K8-1 (-) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
7. |
INSPECT FRONT NO. 1 SPEAKER ASSEMBLY |
(a) Remove the front No. 1 speaker assembly.
Click here
(b) Inspect the front No. 1 speaker assembly.
Click here
| NG |
|
|
|
8. |
INSPECT REAR SPEAKER ASSEMBLY |
(a) Remove the rear speaker assembly.
Click here
(b) Inspect the rear speaker assembly.
Click here
| NG |
|
|
|
9. |
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY |
(a) Remove the front No. 2 speaker assembly.
Click here
(b) Inspect the front No. 2 speaker assembly.
Click here
(c) Clear the DTCs.
Body Electrical > Navigation System > Clear DTCs
(d) Recheck for DTCs and check that no DTCs are output.
Body Electrical > Navigation System > Trouble Codes
OK:
No DTCs are output.
| OK |
|
END |
| NG |
|
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY
|
|
10. |
CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY, DCM (TELEMATICS TRANSCEIVER) OR SPEAKERS - BODY GROUND) |
(a) Disconnect the K14 stereo component amplifier assembly connector.
(b) Disconnect the K139 DCM (telematics transceiver) connector.
(c) Disconnect the K95 front No. 2 speaker assembly LH connector.
(d) Disconnect the K109 and K110 front No. 3 speaker assembly connectors.
(e) Disconnect the P7 and Q7 rear speaker assembly connectors.
(f) Disconnect the R1 rear stereo component speaker assembly connector.
(g) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
K14-14 (TWR+) or K139-1 (SPI+) - Body ground |
Always |
10 kΩ or higher |
|
K14-29 (TWR-) or K139-2 (SPI-) - Body ground |
Always |
10 kΩ or higher |
|
K14-12 (TWL+) or K95-2 (TWL+) - Body ground |
Always |
10 kΩ or higher |
|
K14-27 (TWL-) or K95-1 (TWL-) - Body ground |
Always |
10 kΩ or higher |
|
K14-15 (FR+) or K109-4 (+TW) - Body ground |
Always |
10 kΩ or higher |
|
K14-30 (FR-) or K109-2 (-TW) - Body ground |
Always |
10 kΩ or higher |
|
K14-13 (FL+) or K110-4 (+TW) - Body ground |
Always |
10 kΩ or higher |
|
K14-28 (FL-) or K110-2 (-TW) - Body ground |
Always |
10 kΩ or higher |
|
K14-11 (RR+) or P7-2 - Body ground |
Always |
10 kΩ or higher |
|
K14-26 (RR-) or P7-1 - Body ground |
Always |
10 kΩ or higher |
|
K14-9 (RL+) or Q7-2 - Body ground |
Always |
10 kΩ or higher |
|
K14-24 (RL-) or Q7-1 - Body ground |
Always |
10 kΩ or higher |
|
K14-10 (WF1+) or R1-4 (WF1+) - Body ground |
Always |
10 kΩ or higher |
|
K14-25 (WF1-) or R1-3 (WF1-) - Body ground |
Always |
10 kΩ or higher |
|
K14-8 (WF2+) or R1-2 (WF2+) - Body ground |
Always |
10 kΩ or higher |
|
K14-23 (WF2-) or R1-1 (WF2-) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
11. |
CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) OR SPEAKER - BODY GROUND) |
(a) Disconnect the K139 DCM (telematics transceiver) connector.
(b) Disconnect the K94 front No. 2 speaker assembly RH connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
K139-3 (SPO+) or K94-2 (TWR+) - Body ground |
Always |
10 kΩ or higher |
|
K139-4 (SPO-) or K94-1 (TWR-) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
12. |
INSPECT DCM (TELEMATICS TRANSCEIVER) |
(a) Remove the DCM (telematics transceiver).
Click here
|
(b) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
| OK |
|
| NG |
|
REPLACE DCM (TELEMATICS TRANSCEIVER)
|
|
13. |
CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY OR SPEAKERS - BODY GROUND) |
(a) Disconnect the K14 stereo component amplifier assembly connector.
(b) Disconnect the K109 and K110 front No. 3 speaker assembly connectors.
(c) Disconnect the K94 and K95 front No. 2 speaker assembly connectors.
(d) Disconnect the P7 and Q7 rear speaker assembly connectors.
(e) Disconnect the R1 rear stereo component speaker assembly connector.
(f) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
K14-15 (FR+) or K109-4 (+TW) - Body ground |
Always |
10 kΩ or higher |
|
K14-30 (FR-) or K109-2 (-TW) - Body ground |
Always |
10 kΩ or higher |
|
K14-13 (FL+) or K110-4 (+TW) - Body ground |
Always |
10 kΩ or higher |
|
K14-28 (FL-) or K110-2 (-TW) - Body ground |
Always |
10 kΩ or higher |
|
K14-14 (TWR+) or K94-2 (TWR+) - Body ground |
Always |
10 kΩ or higher |
|
K14-29 (TWR-) or K94-1 (TWR-) - Body ground |
Always |
10 kΩ or higher |
|
K14-12 (TWL+) or K95-2 (TWL+) - Body ground |
Always |
10 kΩ or higher |
|
K14-27 (TWL-) or K95-1 (TWL-) - Body ground |
Always |
10 kΩ or higher |
|
K14-11 (RR+) or P7-2 - Body ground |
Always |
10 kΩ or higher |
|
K14-26 (RR-) or P7-1 - Body ground |
Always |
10 kΩ or higher |
|
K14-9 (RL+) or Q7-2 - Body ground |
Always |
10 kΩ or higher |
|
K14-24 (RL-) or Q7-1 - Body ground |
Always |
10 kΩ or higher |
|
K14-10 (WF1+) or R1-4 (WF1+) - Body ground |
Always |
10 kΩ or higher |
|
K14-25 (WF1-) or R1-3 (WF1-) - Body ground |
Always |
10 kΩ or higher |
|
K14-8 (WF2+) or R1-2 (WF2+) - Body ground |
Always |
10 kΩ or higher |
|
K14-23 (WF2-) or R1-1 (WF2-) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
14. |
CHECK HARNESS AND CONNECTOR (FRONT NO. 1 SPEAKER ASSEMBLY OR FRONT NO. 3 SPEAKER ASSEMBLY - BODY GROUND) |
(a) Disconnect the N1 and O1 front No. 1 speaker assembly connectors.
(b) Disconnect the K109 and K110 front No. 3 speaker assembly connectors.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
N1-2 or K109-3 (+) - Body ground |
Always |
10 kΩ or higher |
|
N1-1 or K109-1 (-) - Body ground |
Always |
10 kΩ or higher |
|
O1-2 or K110-3 (+) - Body ground |
Always |
10 kΩ or higher |
|
O1-1 or K110-1 (-) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
15. |
INSPECT FRONT NO. 1 SPEAKER ASSEMBLY |
(a) Remove the front No. 1 speaker assembly.
Click here
(b) Inspect the front No. 1 speaker assembly.
Click here
| NG |
|
|
|
16. |
INSPECT FRONT NO. 2 SPEAKER ASSEMBLY |
(a) Remove the front No. 2 speaker assembly.
Click here
(b) Inspect the front No. 2 speaker assembly.
Click here
| NG |
|
|
|
17. |
INSPECT REAR SPEAKER ASSEMBLY |
(a) Remove the rear speaker assembly.
Click here
(b) Inspect the rear speaker assembly.
Click here
| NG |
|
|
|
18. |
INSPECT REAR STEREO COMPONENT SPEAKER ASSEMBLY |
(a) Remove the rear stereo component speaker assembly.
Click here
(b) Inspect the rear stereo component speaker assembly.
Click here
| NG |
|
REPLACE REAR STEREO COMPONENT SPEAKER ASSEMBLY
|
|
|
19. |
REPLACE FRONT NO. 3 SPEAKER ASSEMBLY |
(a) Remove the front No. 3 speaker assembly.
Click here
(b) Inspect the front No. 3 speaker assembly.
Click here
(c) Clear the DTCs.
Body Electrical > Navigation System > Clear DTCs
(d) Recheck for DTCs and check that no DTCs are output.
Body Electrical > Navigation System > Trouble Codes
OK:
No DTCs are output.
| OK |
|
END |
| NG |
|
REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY
|
|
|