Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM100000001KCW4
Model Year Start: 2020 Model: Camry Prod Date Range: [09/2019 - 10/2020]
Title: UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE): OIL COOLER: REMOVAL; 2020 MY Camry [09/2019 - 10/2020]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during transmission oil cooler removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Battery terminal is disconnected/reconnected

Perform steering sensor zero point calibration

Lane departure alert system (w/ Steering Control)

2018 - 2020 MY Camry [03/2017 - 10/2020]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Pre-collision system

Intelligent clearance sonar system*1

Memorize steering angle neutral point

Parking assist monitor system

2018 - 2024 MY Camry [03/2017 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION

Panoramic view monitor system

2018 - 2020 MY Camry [06/2017 - 10/2020]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: INITIALIZATION

Replacement of ECM

Vehicle Identification Number (VIN) registration

MIL comes on

2018 - 2024 MY Camry [06/2017 -        ]; 2GR-FKS (ENGINE CONTROL): SFI SYSTEM: REGISTRATION

ECU communication ID registration (Immobiliser system)

Engine start function

2020 - 2022 MY Camry [09/2019 - 08/2022]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): REGISTRATION

Replacement of ECM

(If possible, read the transaxle compensation code from the previous ECM)
  1. Reset memory*2
  2. Transfer transaxle compensation code
  3. Perform road test to allow ECM to learn
  • Large shift shock
  • Deterioration of fuel efficiency

2019 - 2024 MY Camry [08/2018 -        ]; UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: INITIALIZATION for Initialization

2018 - 2024 MY Camry [06/2017 -        ]; UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: REGISTRATION for Registration

Replacement of ECM

(If impossible, read the transaxle compensation code from the previous ECM)
  1. Reset memory*2
  2. Reset transaxle compensation code
  3. Perform road test to allow ECM to learn

Replacement of ECM

Code registration (Smart key System (for Start Function))
  • Wireless door lock control system
  • Smart key system (for Entry Function)
  • Smart key system (for Start Function)
  • Steering lock function

2020 - 2022 MY Camry [09/2019 - 08/2022]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): REGISTRATION

Replacement of automatic transaxle fluid

ATF thermal degradation estimate reset

The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly.

2019 - 2024 MY Camry [08/2018 -        ]; UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: INITIALIZATION

  • *1: When performing learning using the Techstream.

    Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; PARK ASSIST / MONITORING: INTELLIGENT CLEARANCE SONAR SYSTEM: CALIBRATION

  • *2: When the ECM is replaced with a new one, reset memory is unnecessary.

PROCEDURE

1. REMOVE BATTERY

Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; MAINTENANCE: 2GR-FKS BATTERY: REMOVAL

2. REMOVE ECM

Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; 2GR-FKS (ENGINE CONTROL): ECM: REMOVAL

3. REMOVE BATTERY CLAMP SUB-ASSEMBLY

Click here 2019 - 2020 MY Camry [08/2018 - 10/2020]; 2GR-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

4. REMOVE FRONT WHEEL LH

Click here 2018 - 2024 MY Camry [06/2017 -        ]; MAINTENANCE: TIRE AND WHEEL: REMOVAL

5. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH

Click here 2019 - 2020 MY Camry [08/2018 - 10/2020]; 2GR-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

6. REMOVE FRONT WHEEL OPENING EXTENSION PAD RH

Click here 2019 - 2020 MY Camry [08/2018 - 10/2020]; 2GR-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

7. REMOVE NO. 1 ENGINE UNDER COVER

Click here 2019 - 2020 MY Camry [08/2018 - 10/2020]; 2GR-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

8. REMOVE REAR ENGINE UNDER COVER LH

Click here 2019 - 2020 MY Camry [08/2018 - 10/2020]; 2GR-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

9. REMOVE FRONT FENDER APRON SEAL LH

Click here 2019 - 2020 MY Camry [08/2018 - 10/2020]; 2GR-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

10. DRAIN ENGINE COOLANT

Click here 2018 - 2024 MY Camry [06/2017 -        ]; MAINTENANCE: 2GR-FKS COOLANT: REPLACEMENT+

11. DRAIN AUTOMATIC TRANSAXLE FLUID

Click here 2019 - 2021 MY Camry [08/2018 - 08/2021]; UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE): TRANSMISSION WIRE: REMOVAL+

12. DISCONNECT OUTLET NO. 1 OIL COOLER HOSE

(a) Slide the clip and disconnect the outlet No. 1 oil cooler hose from the oil cooler union sub-assembly.

HINT:

Use a container to catch any automatic transaxle fluid which flows out of the outlet No. 1 oil cooler hose and oil cooler union sub-assembly.

13. DISCONNECT INLET NO. 1 OIL COOLER HOSE

(a) Slide the clip and disconnect the inlet No. 1 oil cooler hose from the No. 1 oil cooler outlet tube sub-assembly.

HINT:

Use a container to catch any automatic transaxle fluid which flows out of the inlet No. 1 oil cooler hose and No. 1 oil cooler outlet tube sub-assembly.

14. REMOVE NO. 1 OIL COOLER TUBE SUB-ASSEMBLY WITHOUT HOSE

(a) Remove the 2 bolts to disconnect the No. 1 oil cooler tube sub-assembly without hose from the automatic transaxle case sub-assembly.

(b) Slide the clip and disconnect the inlet No. 2 oil cooler hose from the transmission oil cooler.

HINT:

Use a container to catch any automatic transaxle fluid which flows out of the inlet No. 2 oil cooler hose and transmission oil cooler.

(c) Slide the clip and disconnect the outlet No. 2 oil cooler hose to remove the No. 1 oil cooler tube sub-assembly without hose from the transmission oil cooler.

HINT:

Use a container to catch any automatic transaxle fluid which flows out of the outlet No. 2 oil cooler hose and transmission oil cooler.

(d) Slide the 4 clips and remove the inlet No. 1 oil cooler hose, inlet No. 2 oil cooler hose, outlet No. 1 oil cooler hose and outlet No. 2 oil cooler hose from the No. 1 oil cooler tube sub-assembly without hose.

*1

No. 1 Oil Cooler Tube Sub-assembly without Hose

*2

Inlet No. 1 Oil Cooler Hose

*3

Inlet No. 2 Oil Cooler Hose

*4

Outlet No. 1 Oil Cooler Hose

*5

Outlet No. 2 Oil Cooler Hose

15. DISCONNECT NO. 1 WATER BY-PASS HOSE

(a) Disengage the 3 clamps to remove the transmission breather clamp.

(b) Slide the clip and disconnect the No. 1 water by-pass hose from the transmission oil cooler.

HINT:

Use a container to catch any coolant which flows out of the No. 1 water by-pass hose and transmission oil cooler.

16. DISCONNECT WATER BY-PASS HOSE ASSEMBLY

(a) Slide the clip and disconnect the water by-pass hose assembly from the transmission oil cooler.

HINT:

Use a container to catch any coolant which flows out of the water by-pass hose assembly and transmission oil cooler.

17. REMOVE TRANSMISSION OIL COOLER

(a) Remove the 3 bolts and transmission oil cooler from the automatic transaxle case sub-assembly.

HINT:

Use a container to catch any coolant and automatic transaxle fluid which flow out of the transmission oil cooler.