| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM100000001KAG8 |
| Model Year Start: 2020 | Model: Camry | Prod Date Range: [09/2019 - 10/2020] |
| Title: EXTERIOR PANELS / TRIM: FRONT BUMPER: REASSEMBLY; 2020 MY Camry [09/2019 - 10/2020] | ||
REASSEMBLY
PROCEDURE
1. INSTALL FRONT BUMPER SIDE RETAINER LH
(a) Engage the 2 clips as shown in the illustration.
|
Install in this Direction |
|
(b) Install the front bumper side retainer LH with the bolt. Torque: 7.0 N·m {71 kgf·cm, 62 in·lbf} |
|
2. INSTALL FRONT BUMPER SIDE RETAINER RH
HINT:
Use the same procedure as for the LH side.
3. INSTALL FRONT BUMPER REINFORCEMENT
(a) Install the front bumper reinforcement with the 8 bolts.
Torque:
43 N·m {438 kgf·cm, 32 ft·lbf}
|
(b) Engage the 5 clamps. |
|
(c) Install the headlight assembly LH.
Click here
![2018 - 2024 MY Camry [06/2017 - ]; LIGHTING (EXT): HEADLIGHT ASSEMBLY: INSTALLATION+](/t3Portal/stylegraphics/info.gif)
(d) Install the headlight assembly RH.
HINT:
Use the same procedure as for the LH side.
4. INSTALL FRONT BUMPER ENERGY ABSORBER
(a) Engage the 4 guides to install the front bumper energy absorber as shown in the illustration.
|
|
Install in this Direction |
5. INSTALL NO. 2 FRONT BUMPER ENERGY ABSORBER
(a) Engage the 2 guides to install the No. 2 front bumper energy absorber as shown in the illustration.
|
|
Install in this Direction |
6. INSTALL FRONT FENDER LINER RETAINER
(a) Engage the 2 claws to install the 2 front fender liner retainers as shown in the illustration.
|
|
Install in this Direction |
HINT:
Use the same procedure for the RH side and LH side.
7. INSTALL RADIATOR GRILLE SIDE MOULDING LH (for Mesh Type Radiator Grille)
|
(a) Engage the 2 guides and 2 claws. |
|
|
(b) Install the radiator grille side moulding LH with the 2 clips. |
|
8. INSTALL RADIATOR GRILLE SIDE MOULDING RH (for Mesh Type Radiator Grille)
HINT:
Use the same procedure as for the LH side.
9. INSTALL LOWER RADIATOR GRILLE SUB-ASSEMBLY (for Bar Type Radiator Grille)
(a) Engage the 23 claws.
|
(b) Install the lower radiator grille sub-assembly with the 6 screws. |
|
10. INSTALL LOWER RADIATOR GRILLE SUB-ASSEMBLY (for Mesh Type Radiator Grille)
(a) Engage the 18 claws.
|
(b) Install the lower radiator grille sub-assembly with the 2 screws. |
|
11. INSTALL FOG LIGHT COVER LH (for Mesh Type Radiator Grille)
|
(a) Engage the 6 claws to install the fog light cover LH. |
|
12. INSTALL FOG LIGHT COVER RH (for Mesh Type Radiator Grille)
HINT:
Use the same procedure as for the LH side.
13. INSTALL LOWER RADIATOR GRILLE MOULDING LH (for Mesh Type Radiator Grille)
(a) except TRD:
|
(1) Engage the 10 claws to install the lower radiator grille moulding LH. |
|
14. INSTALL LOWER RADIATOR GRILLE MOULDING RH (for Mesh Type Radiator Grille)
except TRD:
HINT:
Use the same procedure as for the LH side.
15. INSTALL LOWER RADIATOR GRILLE MOULDING (for Mesh Type Radiator Grille)
(a) except TRD:
(1) Engage the 16 claws.
|
(2) Install the lower radiator grille moulding with the 2 screws. |
|
16. INSTALL RADIATOR GRILLE (for Bar Type Radiator Grille)
|
(a) Install the 6 screws. |
|
|
(b) Install the radiator grille with the 2 clips. |
|
17. INSTALL RADIATOR GRILLE (for Mesh Type Radiator Grille)
|
(a) Install the 10 screws. |
|
|
(b) Install the radiator grille with the 2 clips. |
|
18. INSTALL RADIATOR GRILLE SIDE MOULDING LH (for Bar Type Radiator Grille)
(a) Engage the 3 claws as shown in the illustration.
|
|
Install in this Direction |
|
(b) Install the radiator grille side moulding LH with the screw. |
|
19. INSTALL RADIATOR GRILLE SIDE MOULDING RH (for Bar Type Radiator Grille)
HINT:
Use the same procedure as for the LH side.
20. INSTALL RADIATOR GRILLE EMBLEM ASSEMBLY
|
(a) Engage the guide and 2 claws. |
|
|
(b) Install the radiator grille emblem assembly with the 2 screws. |
|
21. INSTALL HOOD TO FRONT END PANEL SEAL
HINT:
When installing the hood to front end panel seal, heat the front bumper cover using a heat light.
Heating Temperature
|
Item |
Temperature |
|---|---|
|
Front Bumper Cover |
20 to 30°C (68 to 86°F) |
CAUTION:
- Do not touch the heat light and heated parts, touching the heat light may result in burns.
- Touching heated parts for a long time may result in burns.
|
*a |
Heated Part |
|
*b |
Heat Light |
NOTICE:
Do not heat the front bumper cover excessively.
(a) Clean the front bumper cover surface.
(1) Using a heat light, heat the front bumper cover surface.
(2) Remove any remaining double-sided tape from the front bumper cover.
(3) Wipe off any tape adhesive residue with cleaner.
(b) Remove the release paper from a new hood to front end panel seal.
HINT:
After removing the release paper, keep the exposed adhesive free from foreign matter.
(c) Engage the guide to attach the double-sided tape as shown in the illustration.
|
Double-sided Tape |
HINT:
Press the hood to front end panel seal firmly to install it.
|
(d) Engage the 6 clips to install the hood to front end panel seal. |
|
22. INSTALL FRONT SPOILER (for TRD)
HINT:
When installing the front spoiler, heat the front bumper cover using a heat light.
Heating Temperature
|
Item |
Temperature |
|---|---|
|
Front Bumper Cover |
20 to 30°C (68 to 86°F) |
CAUTION:
- Do not touch the heat light and heated parts, touching the heat light may result in burns.
- Touching heated parts for a long time may result in burns.
|
*a |
Heated Part |
|
*b |
Heat Light |
NOTICE:
Do not heat the front bumper cover excessively.
(a) Clean the front bumper cover surface.
(1) Using a heat light, heat the front bumper cover surface.
(2) Remove the double-sided tape from the front bumper cover.
(3) Wipe off any tape adhesive residue with cleaner.
(b) Engage the 30 claws.
(c) Remove the release paper from a new front spoiler.
HINT:
After removing the release paper, keep the exposed adhesive free from foreign matter.
(d) Attach the double-sided tape as shown in the illustration.
|
|
Double-sided Tape |
HINT:
- Press the front spoiler firmly to install it.
- Use the same procedure for the RH side and LH side.
(e) Install the front spoiler with the 2 screws and 2 clips.
HINT:
Use the same procedure for the RH side and LH side.
|
Screw |
|
Clip |
23. INSTALL NO. 4 ENGINE ROOM WIRE (w/ Intuitive Parking Assist System)
(a) for Bar Type Radiator Grille:
(1) Engage the 10 clamps to install the No. 4 engine room wire.
(b) for Mesh Type Radiator Grille:
(1) Engage the 12 clamps to install the No. 4 engine room wire.
24. INSTALL FRONT CORNER ULTRASONIC SENSOR RETAINER (w/ Intuitive Parking Assist System)
Click here
25. INSTALL FRONT CENTER ULTRASONIC SENSOR RETAINER (w/ Intuitive Parking Assist System)
for Bar Type Radiator Grille:
Click here
26. INSTALL FRONT CORNER ULTRASONIC SENSOR (w/ Intuitive Parking Assist System)
Click here
27. INSTALL FRONT CENTER ULTRASONIC SENSOR (w/ Intuitive Parking Assist System)
Click here
28. INSTALL FRONT TELEVISION CAMERA ASSEMBLY (w/ Panoramic View Monitor System)
for Bar Type Radiator Grille:
Click here
29. INSTALL FRONT TELEVISION CAMERA ASSEMBLY (w/ Panoramic View Monitor System)
for Mesh Type Radiator Grille:
Click here
30. INSTALL FRONT BUMPER COVER INSERT (w/ Panoramic View Monitor System)
|
(a) for Mesh Type Radiator Grille: (1) Engage the 2 claws to install the front bumper cover insert. |
|
31. INSTALL FRONT BUMPER PAD LH (for Bar Type Radiator Grille)
|
(a) Engage the guide and 2 claws to install the front bumper pad LH. |
|
32. INSTALL FRONT BUMPER PAD RH (for Bar Type Radiator Grille)
HINT:
Use the same procedure as for the LH side.
33. INSTALL FRONT BUMPER PAD LH (for Mesh Type Radiator Grille)
|
(a) Engage the guide and 2 claws to install the front bumper pad LH. |
|
34. INSTALL FRONT BUMPER PAD RH (for Mesh Type Radiator Grille)
HINT:
Use the same procedure as for the LH side.
35. INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET (for Bar Type Radiator Grille)
(a) Engage the 2 guides as shown in the illustration.
|
|
Install in this Direction |
|
(b) Install the front bumper extension mounting bracket with the 2 screws. |
|
36. INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET (for Mesh Type Radiator Grille)
(a) Engage the 2 guides as shown in the illustration.
|
|
Install in this Direction |
|
(b) Install the front bumper extension mounting bracket with the 2 screws. |
|
37. INSTALL MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Pre-collision System)
Click here
|
|