| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM100000001KAG4 |
| Model Year Start: 2020 | Model: Camry | Prod Date Range: [09/2019 - 10/2020] |
| Title: EXTERIOR PANELS / TRIM: FRONT BUMPER: DISASSEMBLY; 2020 MY Camry [09/2019 - 10/2020] | ||
DISASSEMBLY
PROCEDURE
1. REMOVE MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Pre-collision System)
Click here
![2018 - 2020 MY Camry [03/2017 - 10/2020]; CRUISE CONTROL: MILLIMETER WAVE RADAR SENSOR: REMOVAL+](/t3Portal/stylegraphics/info.gif)
2. REMOVE FRONT BUMPER EXTENSION MOUNTING BRACKET (for Bar Type Radiator Grille)
|
(a) Remove the 2 screws. |
|
(b) Disengage the 2 guides to remove the front bumper extension mounting bracket as shown in the illustration.
|
Remove in this Direction |
3. REMOVE FRONT BUMPER EXTENSION MOUNTING BRACKET (for Mesh Type Radiator Grille)
|
(a) Remove the 2 screws. |
|
(b) Disengage the 2 guides to remove the front bumper extension mounting bracket as shown in the illustration.
|
|
Remove in this Direction |
4. REMOVE FRONT BUMPER PAD LH (for Bar Type Radiator Grille)
|
(a) Disengage the 2 claws and guide to remove the front bumper pad LH. |
|
5. REMOVE FRONT BUMPER PAD RH (for Bar Type Radiator Grille)
HINT:
Use the same procedure as for the LH side.
6. REMOVE FRONT BUMPER PAD LH (for Mesh Type Radiator Grille)
|
(a) Disengage the 2 claws and guide to remove the front bumper pad LH. |
|
7. REMOVE FRONT BUMPER PAD RH (for Mesh Type Radiator Grille)
HINT:
Use the same procedure as for the LH side.
8. REMOVE FRONT TELEVISION CAMERA ASSEMBLY (w/ Panoramic View Monitor System)
for Bar Type Radiator Grille:
Click here
9. REMOVE FRONT BUMPER COVER INSERT (w/ Panoramic View Monitor System)
(a) for Mesh Type Radiator Grille:
|
(1) Disengage the 2 claws to remove the front bumper cover insert. |
|
10. REMOVE FRONT TELEVISION CAMERA ASSEMBLY (w/ Panoramic View Monitor System)
for Mesh Type Radiator Grille:
Click here
11. REMOVE FRONT CENTER ULTRASONIC SENSOR (w/ Intuitive Parking Assist System)
Click here
12. REMOVE FRONT CORNER ULTRASONIC SENSOR (w/ Intuitive Parking Assist System)
Click here
13. REMOVE FRONT CENTER ULTRASONIC SENSOR RETAINER (w/ Intuitive Parking Assist System)
for Bar Type Radiator Grille:
Click here
14. REMOVE FRONT CORNER ULTRASONIC SENSOR RETAINER (w/ Intuitive Parking Assist System)
Click here
15. REMOVE NO. 4 ENGINE ROOM WIRE (w/ Intuitive Parking Assist System)
(a) for Bar Type Radiator Grille:
(1) Disengage the 10 clamps to remove the No. 4 engine room wire.
(b) for Mesh Type Radiator Grille:
(1) Disengage the 12 clamps to remove the No. 4 engine room wire.
16. REMOVE FRONT SPOILER (for TRD)
(a) Remove the 2 screws and 2 clips.
HINT:
Use the same procedure for the RH side and LH side.
|
Screw |
|
Clip |
(b) Separate the double-sided tape.
|
Double-sided Tape |
HINT:
Use the same procedure for the RH side and LH side.
(c) Disengage the 30 claws to remove the front spoiler.
17. REMOVE HOOD TO FRONT END PANEL SEAL
|
(a) Disengage the 6 clips. |
|
(b) Separate the double-sided tape and disengage the guide to remove the hood to front end panel seal.
|
|
Double-sided Tape |
18. REMOVE RADIATOR GRILLE EMBLEM ASSEMBLY
|
(a) Remove the 2 screws. |
|
|
(b) Disengage the 2 claws and guide to remove the radiator grille emblem assembly. |
|
19. REMOVE RADIATOR GRILLE SIDE MOULDING LH (for Bar Type Radiator Grille)
|
(a) Remove the screw. |
|
(b) Disengage the 3 claws to remove the radiator grille side moulding LH as shown in the illustration.
|
|
Remove in this Direction |
20. REMOVE RADIATOR GRILLE SIDE MOULDING RH (for Bar Type Radiator Grille)
HINT:
Use the same procedure as for the LH side.
21. REMOVE RADIATOR GRILLE (for Bar Type Radiator Grille)
|
(a) Remove the 2 clips. |
|
|
(b) Remove the 6 screws and radiator grille. |
|
22. REMOVE RADIATOR GRILLE (for Mesh Type Radiator Grille)
|
(a) Remove the 2 clips. |
|
|
(b) Remove the 10 screws and radiator grille. |
|
23. REMOVE LOWER RADIATOR GRILLE MOULDING (for Mesh Type Radiator Grille)
(a) except TRD:
|
(1) Remove the 2 screws. |
|
(2) Disengage the 16 claws to remove the lower radiator grille moulding.
24. REMOVE LOWER RADIATOR GRILLE MOULDING LH (for Mesh Type Radiator Grille)
(a) except TRD:
|
(1) Disengage the 10 claws to remove the lower radiator grille moulding LH. |
|
25. REMOVE LOWER RADIATOR GRILLE MOULDING RH (for Mesh Type Radiator Grille)
except TRD:
HINT:
Use the same procedure as for the LH side.
26. REMOVE FOG LIGHT COVER LH (for Mesh Type Radiator Grille)
|
(a) Disengage the 6 claws to remove the fog light cover LH. |
|
27. REMOVE FOG LIGHT COVER RH (for Mesh Type Radiator Grille)
HINT:
Use the same procedure as for the LH side.
28. REMOVE LOWER RADIATOR GRILLE SUB-ASSEMBLY (for Bar Type Radiator Grille)
|
(a) Remove the 6 screws. |
|
(b) Disengage the 23 claws to remove the lower radiator grille sub-assembly.
29. REMOVE LOWER RADIATOR GRILLE SUB-ASSEMBLY (for Mesh Type Radiator Grille)
|
(a) Remove the 2 screws. |
|
(b) Disengage the 18 claws to remove the lower radiator grille sub-assembly.
30. REMOVE RADIATOR GRILLE SIDE MOULDING LH (for Mesh Type Radiator Grille)
|
(a) Remove the 2 clips. |
|
|
(b) Disengage the 2 claws and 2 guides to remove the radiator grille side moulding LH. |
|
31. REMOVE RADIATOR GRILLE SIDE MOULDING RH (for Mesh Type Radiator Grille)
HINT:
Use the same procedure as for the LH side.
32. REMOVE PIN HOLD CLIP
(a) Disengage the 4 claws to remove the 2 pin hold clips as shown in the illustration.
|
|
Remove in this Direction |
HINT:
Use the same procedure for the RH side and LH side.
33. REMOVE FRONT FENDER LINER RETAINER
(a) Remove the 2 front fender liner retainers as shown in the illustration.
|
|
Remove in this Direction |
HINT:
Use the same procedure for the RH side and LH side.
34. REMOVE NO. 2 FRONT BUMPER ENERGY ABSORBER
(a) Disengage the 2 guides to remove the No. 2 front bumper energy absorber as shown in the illustration.
|
|
Remove in this Direction |
35. REMOVE FRONT BUMPER ENERGY ABSORBER
(a) Disengage the 4 guides to remove the front bumper energy absorber as shown in the illustration.
|
|
Remove in this Direction |
36. REMOVE FRONT BUMPER REINFORCEMENT
(a) Remove the headlight assembly LH.
Click here
(b) Remove the headlight assembly RH.
HINT:
Use the same procedure as for the LH side.
|
(c) Disengage the 5 clamps. |
|
(d) Remove the 8 bolts and front bumper reinforcement.
37. REMOVE FRONT BUMPER SIDE RETAINER LH
|
(a) Remove the bolt. |
|
(b) Disengage the 2 clips to remove the front bumper side retainer LH as shown in the illustration.
|
|
Remove in this Direction |
38. REMOVE FRONT BUMPER SIDE RETAINER RH
HINT:
Use the same procedure as for the LH side.
|
|