| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM100000001JZCF |
| Model Year Start: 2020 | Model: Camry | Prod Date Range: [09/2019 - ] |
| Title: SEAT: FRONT SEAT ASSEMBLY (for TMMK Made Power Seat): INSTALLATION; 2020 - 2024 MY Camry [09/2019 - ] | ||
INSTALLATION
CAUTION / NOTICE / HINT
CAUTION:
-
Be sure to read Precaution thoroughly before servicing.
Click here
![2020 MY Camry [09/2019 - 03/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: PRECAUTION](/t3Portal/stylegraphics/info.gif)
- Wear protective gloves. Sharp areas on the parts may injure your hands.
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. INSTALL FRONT SEAT ASSEMBLY
|
(a) Place the front seat assembly in the cabin. NOTICE: Be careful not to damage the vehicle body. |
|
(b) Connect the front seat airbag assembly connector under the front seat assembly.
(1) Before connecting the connector, check that the position of the housing lock is correct as shown in the illustration.
|
*a |
Correct |
*b |
Incorrect |
|
*c |
Yellow CPA |
- |
- |
(2) Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).
NOTICE:
- When connecting any airbag connector, take care not to damage the airbag wire harness.
- When engaged, the white housing lock will slide. Be sure not to hold the white housing lock and upper part of the yellow CPA, as it may result in an insecure connection.
(c) Connect each connector and engage each clamp under the front seat assembly.
(d) Connect the cable to the negative (-) battery terminal.
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here
(e) Temporarily install the front seat assembly with the 4 bolts.
(f) Operate the slide and vertical power seat switch knob and move the front seat assembly to the rearmost position.
|
(g) Using a T50 "TORX" socket wrench, tighten the 2 bolts on the front side of the front seat assembly. Torque: 37 N·m {377 kgf·cm, 27 ft·lbf} NOTICE: Tighten the bolts in the order shown in the illustration. |
|
(h) Operate the slide and vertical power seat switch knob and move the front seat assembly to the foremost position.
|
(i) Using a T50 "TORX" socket wrench, tighten the 2 bolts on the rear side of the front seat assembly. Torque: 37 N·m {377 kgf·cm, 27 ft·lbf} NOTICE: Tighten the bolts in the order shown in the illustration. |
|
2. INSTALL REAR OUTER SEAT TRACK BRACKET COVER
(a) Engage the claw to install the rear outer seat track bracket cover.
|
Install in this Direction |
3. INSTALL REAR INNER SEAT TRACK BRACKET COVER
(a) Engage the claw to install the rear inner seat track bracket cover.
|
|
Install in this Direction |
4. INSTALL FRONT OUTER SEAT TRACK BRACKET COVER
(a) Operate the slide and vertical power seat switch knob and move the front seat assembly to the rearmost position.
(b) Engage the claw to install the front outer seat track bracket cover.
|
|
Install in this Direction |
5. INSTALL FRONT INNER SEAT TRACK BRACKET COVER
(a) Engage the claw to install the front inner seat track bracket cover.
|
|
Install in this Direction |
6. INSTALL FRONT SEAT HEADREST ASSEMBLY
(a) Install the front seat headrest assembly to the front seat assembly.
7. INSPECT FRONT SEAT ASSEMBLY
Click here
8. CHECK SEAT HEATER
Click here
9. PERFORM DIAGNOSTIC SYSTEM CHECK
Click here
10. INSPECT CLIMATE CONTROL SEAT SYSTEM (w/ Climate Control Seat System)
Click here
11. PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK (for Front Passenger Side)
Click here
12. INSPECT SRS WARNING LIGHT
Click here
|
|