- DTC judgment completed
- System normal
DESCRIPTIONRefer to DTC P107A11.
MONITOR DESCRIPTIONFuel Pressure Sensor Stuck MonitorIf the fuel pressure sensor (fuel delivery pipe with sensor sub-assembly) (for low pressure side) value does not follow the change in the target low pressure side fuel pressure, it is judged as a malfunction. If this malfunction is detected in 2 consecutive driving cycles, the ECM will illuminate the MIL and store DTC P107A2A. Fuel Pressure Sensor Correlation Monitor (Fuel Cut)If the fuel pressure sensor (fuel delivery pipe with sensor sub-assembly) (for low pressure side) value is less than or higher than the threshold value when the fuel pump on the low pressure side is operated at the maximum during a fuel cut, it is judged as a malfunction has occurred. If this malfunction is detected for 2 consecutive driving cycles, the ECM will illuminate the MIL and store DTC P107A64. MONITOR STRATEGY
TYPICAL ENABLING CONDITIONSStuck Monitor
Correlation Monitor (Fuel Cut)
TYPICAL MALFUNCTION THRESHOLDSStuck Monitor
Correlation Monitor (Fuel Cut)
CONFIRMATION DRIVING PATTERNHINT: P107A2A
P107A64
CAUTION / NOTICE / HINTHINT: Read Freeze Frame Data using the Techstream. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred. PROCEDURE
(a) Connect the Techstream to the DLC3. (b) Turn the ignition switch to ON. (c) Turn the Techstream on. (d) Enter the following menus: Powertrain / Engine / Trouble Codes. (e) Read the DTCs and record the Freeze Frame Data. Powertrain > Engine > Trouble Codes
HINT: If any DTCs other than P107A2A, P107A64, P008A00 and/or P008B00 are output, troubleshoot those DTCs first.
(a) Connect the Techstream to the DLC3. (b) Turn the ignition switch to ON. (c) Turn the Techstream on. (d) Enter the following menus: Powertrain / Engine / Data List / Fuel Pressure (Low) / Fuel Pressure 2. Powertrain > Engine > Data List
(e) Start the engine. (f) Record the Fuel Pressure (Low) / Fuel Pressure 2 value. (g) Turn the ignition switch off. (h) Discharge the fuel pressure. HINT: DTCs may be stored during this inspection. Check for DTCs and clear them using the Techstream. (1) Remove the EFI-MAIN NO. 2 fuse from the engine room relay block and junction block assembly. (2) Start the engine. (3) After the engine has stopped on its own, turn the ignition switch off. HINT: If the engine does not stop naturally, perform direct injection by racing the engine to reduce the fuel pressure [Fuel Pressure (High)] and stop the engine. (4) Crank the engine again and make sure that the engine does not start. (5) Install the EFI-MAIN NO. 2 fuse. (i) Turn the ignition switch to ON. (j) Turn the Techstream on. (k) Enter the following menus: Powertrain / Engine / Data List / Fuel Pressure (Low) / Fuel Pressure 2. Powertrain > Engine > Data List
(l) Compare the Fuel Pressure (Low) / Fuel Pressure 2 value recorded with the engine running to the Fuel Pressure (Low) / Fuel Pressure 2 value currently shown on the Techstream.
HINT: Perform "Inspection After Repair" after replacing the fuel pressure sensor (fuel delivery pipe with sensor sub-assembly) (for low pressure side).
(a) Connect the Techstream to the DLC3. (b) Turn the ignition switch to ON. (c) Turn the Techstream on. (d) Clear the DTCs. Powertrain > Engine > Clear DTCs(e) Turn the ignition switch off and wait for at least 30 seconds.
(a) Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern. (b) Enter the following menus: Powertrain / Engine / Utility / All Readiness. Powertrain > Engine > Utility
(c) Input the DTC: P107A2A or P107A64. (d) Check the DTC judgment result.
(a) Install the fuel pressure gauge (for low pressure line of low pressure side). (b) Connect the Techstream to the DLC3. (c) Turn the ignition switch to ON. (d) Turn the Techstream on. (e) Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump Duty Ratio / Data List / Fuel Pressure (Low) / Fuel Pressure 2. Powertrain > Engine > Active Test
(f) Compare the values in the Data List using the Techstream and the fuel pressure gauge when the Active Test was performed. Standard:
HINT: Perform "Inspection After Repair" after replacing the fuel pressure sensor (fuel delivery pipe with sensor sub-assembly) (for low pressure side).
(a) Connect the Techstream to the DLC3. (b) Turn the ignition switch to ON. (c) Turn the Techstream on. (d) Read the Freeze Frame Data value from step 1. Powertrain > Engine > DTC(P107A2A) > Freeze Frame Data
(a) Check around and beneath the vehicle for fuel leaks, fumes, etc. OK: No fuel leaks present.
(a) Connect the Techstream to the DLC3. (b) Turn the ignition switch to ON. (c) Turn the Techstream on. (d) Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump Duty Ratio. Powertrain > Engine > Active Test
(e) Check whether the fuel pump operating sound occurs when performing the Active Test on the Techstream. Standard:
HINT: Perform "Inspection After Repair" after replacing the fuel pump (for low pressure side).
(a) Discharge the fuel pressure. HINT: DTCs may be stored during this inspection. Check for DTCs and clear them using the Techstream. (1) Remove the EFI-MAIN NO. 2 fuse from the engine room relay block and junction block assembly. (2) Start the engine. (3) After the engine has stopped on its own, turn the ignition switch off. HINT: If the engine does not stop naturally, perform direct injection by racing the engine to reduce the fuel pressure [Fuel Pressure (High)] and stop the engine. (4) Crank the engine again and make sure that the engine does not start. (5) Install the EFI-MAIN NO. 2 fuse. (b) Connect the Techstream to the DLC3. (c) Turn the ignition switch to ON. (d) Turn the Techstream on. (e) Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump Duty Ratio / Data List / Fuel Pressure (Low) / Fuel Pressure 2. Powertrain > Engine > Active Test
(f) Read the value displayed on the Techstream when the Active Test was performed. Standard:
HINT: Once the fuel pressure becomes high, the fuel pressure will not decrease, even when switched from High to Low. Therefore, make sure that the fuel pressure is low before checking that the fuel pressure changes when switching from Low to High.
(a) Discharge the fuel pressure. HINT: DTCs may be stored during this inspection. Check for DTCs and clear them using the Techstream. (1) Remove the EFI-MAIN NO. 2 fuse from the engine room relay block and junction block assembly. (2) Start the engine. (3) After the engine has stopped on its own, turn the ignition switch off. HINT: If the engine does not stop naturally, perform direct injection by racing the engine to reduce the fuel pressure [Fuel Pressure (High)] and stop the engine. (4) Crank the engine again and make sure that the engine does not start. (5) Install the EFI-MAIN NO. 2 fuse. (b) Connect the Techstream to the DLC3. (c) Turn the ignition switch to ON. (d) Turn the Techstream on. (e) Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump Duty Ratio / Data List / Fuel Pressure (Low) / Fuel Pressure 2. Powertrain > Engine > Active Test
(f) Read the value displayed on the Techstream when the Active Test was performed. Standard:
HINT: Once the fuel pressure becomes high, the fuel pressure will not decrease, even when switched from High to Low. Therefore, make sure that the fuel pressure is low before checking that the fuel pressure changes when switching from Low to High. OK: Actual Low and High values are as shown above.
(a) Install the fuel pressure gauge (for low pressure line of low pressure side). (b) Connect the Techstream to the DLC3. (c) Turn the ignition switch to ON. (d) Turn the Techstream on. (e) Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump Duty Ratio / Data List / Fuel Pressure (Low) / Fuel Pressure 2. Powertrain > Engine > Active Test
(f) Compare the values in the Data List using the Techstream and the fuel pressure gauge when the Active Test was performed. Standard:
HINT: Perform "Inspection After Repair" after replacing the fuel pressure sensor (fuel delivery pipe with sensor sub-assembly) (for low pressure side).
(a) Connect the Techstream to the DLC3. (b) Turn the ignition switch to ON. (c) Turn the Techstream on. (d) Clear the DTCs. Powertrain > Engine > Clear DTCs(e) Turn the ignition switch off and wait for at least 30 seconds.
(a) Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern. (b) Enter the following menus: Powertrain / Engine / Utility / All Readiness. Powertrain > Engine > Utility
(c) Input the DTC: P107A2A or P107A64. (d) Check the DTC judgment result.
(a) Connect the Techstream to the DLC3. (b) Start the engine. (c) Turn the Techstream on. (d) Enter the following menus: Powertrain / Engine / Data List / Fuel Pressure (Low) / Fuel Pressure 2. Powertrain > Engine > Data List
(e) Record the Fuel Pressure (Low) / Fuel Pressure 2 value. (f) Turn the ignition switch off. (g) Wait for 10 seconds. (h) Turn the ignition switch to ON. (i) Turn the Techstream on. (j) Enter the following menus: Powertrain / Engine / Data List / Fuel Pressure (Low) / Fuel Pressure 2. Powertrain > Engine > Data List
(k) Compare the Fuel Pressure (Low) / Fuel Pressure 2 value recorded with the engine running to the Fuel Pressure (Low) / Fuel Pressure 2 value currently shown on the Techstream.
HINT: Perform "Inspection After Repair" after replacing the fuel pump (for low pressure side).
(a) Install the fuel pressure gauge (for low pressure line of low pressure side). (b) Connect the Techstream to the DLC3. (c) Turn the ignition switch to ON. (d) Turn the Techstream on. (e) Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump Duty Ratio / Data List / Fuel Pressure (Low) / Fuel Pressure 2. Powertrain > Engine > Active Test
(f) Read the values in the Data List using the Techstream and the fuel pressure gauge when the Active Test was performed.
HINT: Perform "Inspection After Repair" after replacing the fuel pressure sensor (fuel delivery pipe with sensor sub-assembly) (for low pressure side).
(a) Connect the Techstream to the DLC3. (b) Start the engine. (c) Turn the Techstream on. (d) Enter the following menus: Powertrain / Engine / Data List / Fuel Pressure (Low) / Fuel Pressure 2. Powertrain > Engine > Data List
(e) Record the Fuel Pressure (Low) / Fuel Pressure 2 value. (f) Turn the ignition switch off. (g) Discharge the fuel pressure. HINT: DTCs may be stored during this inspection. Check for DTCs and clear them using the Techstream. (1) Remove the EFI-MAIN NO. 2 fuse from the engine room relay block and junction block assembly. (2) Start the engine. (3) After the engine has stopped on its own, turn the ignition switch off. HINT: If the engine does not stop naturally, perform direct injection by racing the engine to reduce the fuel pressure [Fuel Pressure (High)] and stop the engine. (4) Crank the engine again and make sure that the engine does not start. (5) Install the EFI-MAIN NO. 2 fuse. (h) Turn the ignition switch to ON. (i) Turn the Techstream on. (j) Enter the following menus: Powertrain / Engine / Data List / Fuel Pressure (Low) / Fuel Pressure 2. Powertrain > Engine > Data List
(k) Compare the Fuel Pressure (Low) / Fuel Pressure 2 value recorded with the engine running to the Fuel Pressure (Low) / Fuel Pressure 2 value currently shown on the Techstream.
HINT: Perform "Inspection After Repair" after replacing the fuel pressure sensor (fuel delivery pipe with sensor sub-assembly) (for low pressure side).
(a) Install the fuel pressure gauge (for low pressure line of low pressure side). (b) Connect the Techstream to the DLC3. (c) Turn the ignition switch to ON. (d) Turn the Techstream on. (e) Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump Duty Ratio / Data List / Fuel Pressure (Low) / Fuel Pressure 2. Powertrain > Engine > Active Test
(f) Compare the values in the Data List using the Techstream and the fuel pressure gauge when the Active Test was performed. Standard:
HINT: Perform "Inspection After Repair" after replacing the fuel pressure sensor (fuel delivery pipe with sensor sub-assembly) (for low pressure side).
(a) Connect the Techstream to the DLC3. (b) Turn the ignition switch to ON. (c) Turn the Techstream on. (d) Clear the DTCs. Powertrain > Engine > Clear DTCs(e) Turn the ignition switch off and wait for at least 30 seconds.
(a) Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern. (b) Enter the following menus: Powertrain / Engine / Utility / All Readiness. Powertrain > Engine > Utility
(c) Input the DTC: P107A2A or P107A64. (d) Check the DTC judgment result.
|