Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM100000001JRAO
Model Year Start: 2020 Model: Camry Prod Date Range: [09/2019 - 10/2020]
Title: AXLE AND DIFFERENTIAL: FRONT AXLE HUB: REMOVAL; 2020 MY Camry [09/2019 - 10/2020]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front axle hub sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Front wheel alignment adjustment

Perform system variant learning and acceleration sensor zero point calibration.

  • VSC disabled or malfunctioning
  • DTCs are output
  • Slip indicator light illuminated
  • ABS warning light illuminated

w/ Electric Parking Brake System: 2018 - 2020 MY Camry [06/2017 - 10/2020]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM (w/ Electric Parking Brake System): CALIBRATION

w/o Electric Parking Brake System: 2018 - 2020 MY Camry [06/2017 - 10/2020]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM (w/o Electric Parking Brake System): CALIBRATION

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.

PROCEDURE

1. REMOVE FRONT WHEEL

Click here 2018 - 2024 MY Camry [06/2017 -        ]; MAINTENANCE: TIRE AND WHEEL: REMOVAL+

2. REMOVE FRONT AXLE SHAFT NUT

for A25A-FKS: Click here 2020 MY Camry [09/2019 - 03/2020]; DRIVE SHAFT / PROPELLER SHAFT: FRONT DRIVE SHAFT ASSEMBLY (for A25A-FKS): REMOVAL+ 2020 MY Camry [03/2020 - 10/2020]; DRIVE SHAFT / PROPELLER SHAFT: FRONT DRIVE SHAFT ASSEMBLY (for A25A-FKS): REMOVAL+

for 2GR-FKS: Click here 2019 - 2020 MY Camry [08/2018 - 10/2020]; DRIVE SHAFT / PROPELLER SHAFT: FRONT DRIVE SHAFT ASSEMBLY (for 2GR-FKS): REMOVAL+

3. SEPARATE FRONT SPEED SENSOR

(a) Remove the bolt and separate the front speed sensor and front flexible hose from the front shock absorber assembly.

NOTICE:

Be sure to separate the front speed sensor and front flexible hose from the front shock absorber assembly completely.

(b) Remove the bolt, disengage the clamp and separate the front speed sensor from the front shock absorber assembly and steering knuckle.

NOTICE:

  • Prevent foreign matter from contacting the sensor tip.
  • Be careful not to damage the front speed sensor.
  • Clean the speed sensor installation hole and the contact surfaces every time the front speed sensor is removed.

4. SEPARATE TIE ROD ASSEMBLY

Click here 2020 MY Camry [09/2019 - 03/2020]; STEERING GEAR / LINKAGE: STEERING GEAR: REMOVAL+ 2020 MY Camry [03/2020 - 10/2020]; STEERING GEAR / LINKAGE: STEERING GEAR: REMOVAL+

5. SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY

Click here 2020 - 2024 MY Camry [09/2019 -        ]; AXLE AND DIFFERENTIAL: FRONT AXLE HUB BOLT: REPLACEMENT+

6. REMOVE FRONT DISC

except 2-Pot Caliper: Click here 2018 - 2024 MY Camry [03/2017 -        ]; BRAKE (FRONT): FRONT BRAKE (except 2-Pot Caliper): REMOVAL+

for 2-Pot Caliper: Click here 2020 - 2024 MY Camry [09/2019 -        ]; BRAKE (FRONT): FRONT BRAKE (for 2-Pot Caliper): REMOVAL+

7. SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY

(a) Remove the bolt and 2 nuts and separate the front lower No. 1 suspension arm sub-assembly from the front lower ball joint assembly.

8. SEPARATE FRONT DRIVE SHAFT ASSEMBLY

(a) Put matchmarks on the front drive shaft assembly and the front axle hub sub-assembly.

*a

Matchmark

(b) Using a plastic hammer, separate the front drive shaft assembly from the front axle assembly.

NOTICE:

  • Do not damage the front drive shaft outboard joint boot.
  • Do not push the front axle assembly towards the outside of the vehicle any further than necessary.

HINT:

If it is difficult to separate the front drive shaft assembly from the front axle assembly, tap the end of the front drive shaft assembly using a brass bar and a hammer.

9. REMOVE FRONT AXLE ASSEMBLY

(a) Remove the 2 bolts, 2 nuts and front axle assembly from the front shock absorber assembly.

NOTICE:

When removing the nuts, keep the bolts from rotating.

10. REMOVE FRONT AXLE HUB SUB-ASSEMBLY

(a) Secure the front axle assembly between aluminum plates in a vise.

NOTICE:

Do not overtighten the vise.

(b) Remove the 4 bolts, front axle hub sub-assembly and front disc brake dust cover from the steering knuckle.

NOTICE:

  • Do not drop the front axle hub sub-assembly.
  • Be careful not to damage the speed sensor rotor or contact surfaces.
  • Do not allow foreign matter to contact the speed sensor rotor or contact surfaces.