Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM100000001E7WF
Model Year Start: 2019 Model: Camry Prod Date Range: [08/2018 - 10/2020]
Title: UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE ASSEMBLY: REMOVAL; 2019 - 2020 MY Camry [08/2018 - 10/2020]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during automatic transaxle assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Battery terminal is disconnected/reconnected

Perform steering sensor zero point calibration

Lane departure alert system (w/ Steering Control)

2018 - 2020 MY Camry [03/2017 - 10/2020]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Pre-collision system

Intelligent clearance sonar system*1

Memorize steering angle neutral point

Parking assist monitor system

2018 - 2024 MY Camry [03/2017 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION

Panoramic view monitor system

2018 - 2020 MY Camry [06/2017 - 10/2020]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: INITIALIZATION

Replacement of ECM

Vehicle Identification Number (VIN) registration

MIL comes on

2018 - 2024 MY Camry [06/2017 -        ]; 2GR-FKS (ENGINE CONTROL): SFI SYSTEM: REGISTRATION

ECU communication ID registration (Immobiliser system)

Engine start function

2018 - 2019 MY Camry [03/2017 - 09/2019]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): REGISTRATION 2020 - 2022 MY Camry [09/2019 - 08/2022]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): REGISTRATION

  • Replacement of engine assembly
  • Gas leak from exhaust system is repaired

Inspection After Repair
  • Poor idle, etc.
  • Engine start function, etc.

2019 MY Camry [08/2018 - 09/2019]; 2GR-FKS (ENGINE CONTROL): SFI SYSTEM: INITIALIZATION 2020 - 2024 MY Camry [09/2019 -        ]; 2GR-FKS (ENGINE CONTROL): SFI SYSTEM: INITIALIZATION

Replacement of automatic transaxle assembly
  1. Reset memory
  2. Input transaxle compensation code into ECM
  3. Perform road test to allow ECM to learn
  • Large shift shock
  • Deterioration of fuel efficiency

2019 - 2024 MY Camry [08/2018 -        ]; UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: INITIALIZATION for Initialization

2018 - 2024 MY Camry [06/2017 -        ]; UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: REGISTRATION for Registration

Replacement of ECM

(If possible, read the transaxle compensation code from the previous ECM)
  1. Reset memory*2
  2. Transfer transaxle compensation code
  3. Perform road test to allow ECM to learn

Replacement of ECM

(If impossible, read the transaxle compensation code from the previous ECM)
  1. Reset memory*2
  2. Reset transaxle compensation code
  3. Perform road test to allow ECM to learn

Replacement of ECM

Code registration (Smart key System (for Start Function))
  • Wireless door lock control system
  • Smart key system (for Entry Function)
  • Smart key system (for Start Function)
  • Steering lock function

2018 - 2019 MY Camry [03/2017 - 09/2019]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): REGISTRATION 2020 - 2022 MY Camry [09/2019 - 08/2022]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): REGISTRATION

Replacement of automatic transaxle fluid

ATF thermal degradation estimate reset

The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly.

2019 - 2024 MY Camry [08/2018 -        ]; UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: INITIALIZATION

Suspension, tires, etc.

(The vehicle height changes because of suspension or tire replacement)

Rear television camera assembly optical axis (Back camera position setting)

Parking assist monitor system

2018 - 2024 MY Camry [03/2017 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION for Initialization

2018 - 2020 MY Camry [06/2017 - 10/2020]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: CALIBRATION for Calibration

Replacement of front bumper assembly

Front television camera view adjustment

Panoramic view monitor system

2018 - 2020 MY Camry [06/2017 - 10/2020]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: INITIALIZATION for Initialization

2018 - 2020 MY Camry [06/2017 - 10/2020]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: CALIBRATION for Calibration

Suspension, tires, etc.

(The vehicle height changes because of suspension or tire replacement)
  • Television camera controller initialization
  • Adjust steering angle
  • Rear television camera assembly optical axis (Back camera position setting)

Front wheel alignment adjustment

Perform system variant learning and acceleration sensor zero point calibration.
  • VSC disabled or malfunctioning
  • DTCs are output
  • Slip indicator light illuminated
  • ABS warning light illuminated

2018 - 2020 MY Camry [06/2017 - 10/2020]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM (w/ Electric Parking Brake System): CALIBRATION

  • *1: When performing learning using the Techstream.

    Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; PARK ASSIST / MONITORING: INTELLIGENT CLEARANCE SONAR SYSTEM: CALIBRATION

  • *2: When the ECM is replaced with a new one, reset memory is unnecessary.

CAUTION:

  • The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop or the engine assembly with transaxle may fall off the engine lifter.

    *a

    An Object Exceeding Weight Limit of Engine Lifter
  • To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.
  • The automatic transaxle assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop.

    *a

    An Object Exceeding Weight Limit of Transmission Jack

PROCEDURE

1. REMOVE FLYWHEEL HOUSING UNDER COVER

Click here 2019 - 2020 MY Camry [08/2018 - 10/2020]; 2GR-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL

2. REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

(a) Turn the crankshaft to gain access to the 6 drive plate and torque converter assembly setting bolts and remove each drive plate and torque converter assembly setting bolt while holding the crankshaft pulley bolt with a wrench.

HINT:

There will be one black colored drive plate and torque converter assembly setting bolt.

3. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

Click here 2019 - 2020 MY Camry [08/2018 - 10/2020]; 2GR-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

4. DISCONNECT VACUUM HOSE

(a) Disconnect the vacuum hose from the rear engine mounting insulator.

(b) Disconnect the vacuum hose from the intake air surge tank assembly.

(c) Disengage the clamp to disconnect the vacuum hose from the hose clamp.

(d) Disengage the 9 clamps to disconnect the vacuum hose from the automatic transaxle assembly.

5. REMOVE STARTER ASSEMBLY

Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; 2GR-FKS (STARTING): STARTER: REMOVAL+

6. REMOVE BREATHER PLUG HOSE

(a) Disengage the 3 hose clamps to disconnect the breather plug hose.

(b) Using a screwdriver with its tip wrapped with protective tape, remove the breather plug hose from the No. 1 breather plug (ATM).

NOTICE:

Be careful not to damage the No. 1 breather plug (ATM).

(c) Remove the breather plug sub-assembly from the breather plug hose.

NOTICE:

Be careful not to damage the breather plug sub-assembly.

*1

Breather Plug Sub-assembly

*2

Breather Plug Hose

7. DISCONNECT NO. 1 WATER BY-PASS HOSE

(a) Disengage the 2 clamps to remove the transmission breather clamp.

(b) Slide the clip and disconnect the No. 1 water by-pass hose from the transmission oil cooler.

HINT:

Use a container to catch any coolant which flows out of the No. 1 water by-pass hose and transmission oil cooler.

8. DISCONNECT WATER BY-PASS HOSE ASSEMBLY

(a) Slide the clip and disconnect the water by-pass hose assembly from the transmission oil cooler.

HINT:

Use a container to catch any coolant which flows out of the water by-pass hose assembly and transmission oil cooler.

(b) Disengage the clamp to disconnect the water by-pass hose assembly from the automatic transaxle assembly.

9. DISCONNECT WIRE HARNESS

(a) Disengage the claw, rotate the lever and disconnect the transmission wire connector.

(b) Disconnect the park/neutral position switch assembly connector.

(c) Disengage the wire harness clamp and disconnect the vacuum switching valve (for active control engine mount system) connector.

(d) Remove the 2 bolts.

(e) Remove the bolt.

(f) Disengage the 2 wire harness clamps to disconnect the wire harness.

(g) Remove the 2 bolts.

(h) Disconnect the rack and pinion power steering gear assembly connector.

HINT:

Release the lock before rotating the lock lever.

(i) Remove the 2 bolts to disconnect the wire harness.

(j) Disengage the 3 wire harness clamps to disconnect the wire harness from the automatic transaxle assembly.

10. INSTALL ENGINE HANGERS

Click here 2019 - 2020 MY Camry [08/2018 - 10/2020]; 2GR-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

11. REMOVE FRONT FRAME ASSEMBLY

Click here 2019 - 2020 MY Camry [08/2018 - 10/2020]; 2GR-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

12. REMOVE FRONT ENGINE MOUNTING BRACKET

(a) Remove the 3 bolts and front engine mounting bracket from the transaxle housing.

13. REMOVE AUTOMATIC TRANSAXLE ASSEMBLY

(a) Support the automatic transaxle assembly with a transmission jack.

NOTICE:

Secure the automatic transaxle assembly to the transmission jack using a suitable adapter, such as a rope or attachment.

(b) Remove the 11 bolts and automatic transaxle assembly.

NOTICE:

To prevent damage to the knock pins, do not pry between the automatic transaxle assembly and engine assembly.

14. REMOVE REAR NO. 2 ENGINE MOUNTING INSULATOR

(a) Remove the 5 bolts and rear No. 2 engine mounting insulator from the automatic transaxle case sub-assembly.

15. REMOVE REAR ENGINE MOUNTING INSULATOR

Click here 2019 - 2020 MY Camry [08/2018 - 10/2020]; 2GR-FKS (ENGINE CONTROL): ACTIVE CONTROL ENGINE MOUNT (for Rear Side): REMOVAL+

16. REMOVE REAR ENGINE MOUNTING BRACKET SUB-ASSEMBLY

(a) Remove the 4 bolts and rear engine mounting bracket sub-assembly from the transaxle housing.

17. DISCONNECT OUTLET NO. 1 OIL COOLER HOSE

Click here 2019 MY Camry [08/2018 - 09/2019]; UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE): OIL COOLER: REMOVAL+ 2020 MY Camry [09/2019 - 10/2020]; UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE): OIL COOLER: REMOVAL+

18. DISCONNECT INLET NO. 1 OIL COOLER HOSE

Click here 2019 MY Camry [08/2018 - 09/2019]; UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE): OIL COOLER: REMOVAL+ 2020 MY Camry [09/2019 - 10/2020]; UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE): OIL COOLER: REMOVAL+

19. REMOVE NO. 1 OIL COOLER TUBE SUB-ASSEMBLY WITHOUT HOSE

Click here 2019 MY Camry [08/2018 - 09/2019]; UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE): OIL COOLER: REMOVAL+ 2020 MY Camry [09/2019 - 10/2020]; UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE): OIL COOLER: REMOVAL+

20. REMOVE TRANSMISSION OIL COOLER

Click here 2019 MY Camry [08/2018 - 09/2019]; UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE): OIL COOLER: REMOVAL+ 2020 MY Camry [09/2019 - 10/2020]; UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE): OIL COOLER: REMOVAL+

21. REMOVE AUTOMATIC TRANSMISSION CASE COVER

(a) Remove the 2 clips and automatic transmission case cover from the automatic transaxle case sub-assembly.

22. REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

(a) Remove the 2 bolts and No. 1 transmission control cable bracket from the automatic transaxle case sub-assembly.

23. REMOVE TRANSMISSION CASE PLUG ASSEMBLY

(a) Remove the transmission case plug assembly from the transaxle housing.

24. REMOVE WIRE HARNESS CLAMP BRACKET

(a) Remove the bolt and wire harness clamp bracket from the automatic transaxle case sub-assembly.

(b) Remove the 2 bolts and 2 wire harness clamp brackets from the automatic transaxle case sub-assembly.

25. REMOVE TORQUE CONVERTER ASSEMBLY

(a) Remove the torque converter assembly from the automatic transaxle assembly.

26. INSPECT TORQUE CONVERTER ASSEMBLY

Click here 2018 - 2024 MY Camry [06/2017 -        ]; UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE): TORQUE CONVERTER AND DRIVE PLATE: INSPECTION+

27. INSPECT DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

Click here 2018 - 2024 MY Camry [06/2017 -        ]; UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE): TORQUE CONVERTER AND DRIVE PLATE: INSPECTION+