Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM100000001E7W2
Model Year Start: 2019 Model: Camry Prod Date Range: [08/2018 - 09/2019]
Title: UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE): TRANSMISSION WIRE: REMOVAL; 2019 MY Camry [08/2018 - 09/2019]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during transmission wire removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

*: except Mexico Models

Replacement of automatic transaxle fluid*

ATF thermal degradation estimate reset

The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly.

2019 MY Camry [08/2018 - 09/2019]; UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: INITIALIZATION

PROCEDURE

1. REMOVE FRONT WHEEL LH

Click here 2018 - 2024 MY Camry [06/2017 -        ]; MAINTENANCE: TIRE AND WHEEL: REMOVAL

2. REMOVE FRONT WHEEL OPENING EXTENSION PAD RH

Click here 2019 MY Camry [08/2018 - 09/2019]; A25A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

3. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH

Click here 2019 MY Camry [08/2018 - 09/2019]; A25A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

4. REMOVE NO. 1 ENGINE UNDER COVER

Click here 2019 MY Camry [08/2018 - 09/2019]; A25A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

5. REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY

Click here 2019 MY Camry [08/2018 - 09/2019]; A25A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

6. REMOVE FRONT FENDER APRON SEAL LH

Click here 2019 MY Camry [08/2018 - 09/2019]; A25A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

7. DRAIN AUTOMATIC TRANSAXLE FLUID

(a) Remove the refill plug and gasket from the automatic transaxle case sub-assembly.

(b) Using a 10 mm hexagon socket wrench, remove the overflow plug and gasket from the transaxle housing.

(c) Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the transaxle housing and drain the automatic transaxle fluid.

*1

No. 1 Transmission Oil Filler Tube

(d) Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the transaxle housing.

Torque:

1.7 N·m {17 kgf·cm, 15 in·lbf}

(e) Using a 10 mm hexagon socket wrench, temporarily install the gasket and overflow plug to the transaxle housing.

HINT:

Reuse the old gasket as the overflow plug will be removed again to adjust the automatic transaxle fluid level.

(f) Temporarily install the gasket and refill plug to avoid automatic transaxle fluid spillage.

HINT:

Reuse the old gasket as the refill plug will be removed again to adjust the automatic transaxle fluid level.

8. REMOVE VACUUM SWITCHING VALVE (for Active Control Engine Mount System)

Click here 2018 - 2024 MY Camry [03/2017 -        ]; A25A-FKS (ENGINE CONTROL): VACUUM SWITCHING VALVE (for Engine Mounting): REMOVAL

9. REMOVE FRONT ENGINE MOUNTING INSULATOR

Click here 2018 - 2020 MY Camry [03/2017 - 03/2020]; A25A-FKS (ENGINE CONTROL): ACTIVE CONTROL ENGINE MOUNT (for Front Side): REMOVAL+

10. REMOVE FRONT SUSPENSION MEMBER DYNAMIC DAMPER

Click here 2019 MY Camry [08/2018 - 09/2019]; FRONT SUSPENSION: FRONT SUSPENSION MEMBER: REMOVAL+

11. SEPARATE OIL COOLER UNION SUB-ASSEMBLY

(a) Remove the bolt to separate the oil cooler union sub-assembly bracket portion from the automatic transaxle case sub-assembly.

*1

Oil Cooler Union Bolt

(b) Remove the oil cooler union bolt and 2 gaskets to separate the oil cooler union sub-assembly from the automatic transaxle case sub-assembly.

12. REMOVE TRANSMISSION CASE SIDE COVER

(a) Remove the 10 bolts and transmission case side cover from the automatic transaxle case sub-assembly.

*A

for TMC, AISIN AW Made

*B

for TMMWV Made

13. REMOVE TRANSMISSION WIRE

(a) Disengage the claw, rotate the lever and disconnect the transmission wire connector.

(b) Disengage the clamp to disconnect the transmission wire from the solenoid lock plate.

*a

Connector (A)

*b

Connector (B)

(c) Disconnect the 9 solenoid valve connectors.

HINT:

  • Using a screwdriver, disconnect the solenoid valve connector (A) using the procedure shown in the illustration.
  • Using a screwdriver, disconnect the solenoid valve connector (B) using the procedure shown in the illustration.

(d) Remove the bolt and temperature sensor clamp and disconnect the temperature sensor from the transmission valve body assembly.

(e) Disconnect the transmission revolution sensor (NT) connector and transmission revolution sensor (NC) connector.

(f) Remove the bolt and transmission wire from the automatic transaxle case sub-assembly.