Last Modified: 11-20-2023 |
6.11:8.1.0 |
Doc ID: RM100000001DVS1 |
Model Year Start: 2019 |
Model: Camry |
Prod Date Range: [08/2018 -
] |
Title: A25A-FKS (ENGINE CONTROL): SFI SYSTEM: P022011; Throttle/Pedal Position Sensor/Switch "B" Circuit Short to Ground; 2019 - 2024 MY Camry [08/2018 - ] |
DTC
|
P022011
|
Throttle/Pedal Position Sensor/Switch "B" Circuit Short to Ground
|
DESCRIPTION
Refer to DTC P012011.
Click here
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
MIL
|
Memory
|
Note
|
P022011
|
Throttle/Pedal Position Sensor/Switch "B" Circuit Short to Ground
|
The output voltage of VTA2 is less than 2.05 V for 2 seconds or more (1 trip detection logic).
|
-
Throttle position sensor (throttle body with motor assembly)
-
Short in VTA2 circuit
-
Open in VCTA circuit
-
ECM
|
Comes on
|
DTC stored
|
-
SAE Code: P0222
-
DTC for Mexico Models: Applies
|
MONITOR DESCRIPTION
The ECM uses the throttle position sensor to monitor the throttle valve opening angle. If the VTA2 terminal voltage is less than the threshold, the ECM will illuminate the MIL and store this DTC.
MONITOR STRATEGY
Related DTCs
|
P0222: Throttle position sensor 2 range check (low voltage)
|
Required Sensors/Components (Main)
|
Throttle position sensor
|
Required Sensors/Components (Related)
|
-
|
Frequency of Operation
|
Continuous
|
Duration
|
2 seconds
|
MIL Operation
|
Immediate
|
Sequence of Operation
|
None
|
TYPICAL ENABLING CONDITIONS
Monitor runs whenever the following DTCs are not stored
|
None
|
Both of the following conditions are met
|
-
|
Battery voltage
|
8 V or higher
|
Ignition switch
|
ON
|
TYPICAL MALFUNCTION THRESHOLDS
VTA2 voltage
|
Less than 2.05 V
|
CONFIRMATION DRIVING PATTERN
HINT:
-
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here
-
When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here
-
Connect the Techstream to the DLC3.
-
Turn the ignition switch to ON.
-
Turn the Techstream on.
-
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
-
Turn the ignition switch off and wait for at least 30 seconds.
-
Turn the ignition switch to ON [A].
-
Turn the Techstream on.
-
Start the engine.
-
With the vehicle stationary, fully depress and release the accelerator pedal [B].
-
Idle the engine for 2 seconds or more [C].
-
Enter the following menus: Powertrain / Engine / Trouble Codes [D].
-
Read the pending DTCs.
HINT:
-
If a pending DTC is output, the system is malfunctioning.
-
If a pending DTC is not output, perform the following procedure.
-
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
-
Input the DTC: P022011.
-
Check the DTC judgment result.
Techstream Display
|
Description
|
NORMAL
|
-
DTC judgment completed
-
System normal
|
ABNORMAL
|
-
DTC judgment completed
-
System abnormal
|
INCOMPLETE
|
-
DTC judgment not completed
-
Perform driving pattern after confirming DTC enabling conditions
|
FAIL-SAFE
When this DTC is stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 7.5° throttle valve opening angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal angle, to allow the vehicle to continue running at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.
Fail-safe mode continues until a pass condition is detected, and the ignition switch is turned off.
WIRING DIAGRAM
Refer to DTC P012011.
Click here
CAUTION / NOTICE / HINT
HINT:
Read Freeze Frame Data using the Techstream. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
1.
|
READ VALUE USING TECHSTREAM (THROTTLE POSITION SENSOR NO.2 VOLTAGE)
|
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine / Data List / Throttle Position Sensor No.2 Voltage.
Powertrain > Engine > Data List
Tester Display
|
Throttle Position Sensor No.2 Voltage
|
(e) Read the values displayed on the Techstream.
(f) Disconnect the throttle body with motor assembly connector.
(g) Compare the value of the Data List item Throttle Position Sensor No.2 Voltage after disconnecting the throttle body with motor assembly connector to the value when the connector was connected.
Result
|
Proceed to
|
Changes from less than 2.05 V to higher than 4.75 V
|
A
|
Does not change from less than 2.05 V
|
B
|
HINT:
Perform "Inspection After Repair" after replacing the throttle body with motor assembly.
Click here
B
|
|
|
2.
|
CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)
|
(a) Disconnect the throttle body with motor assembly connector.
(b) Disconnect the ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
C27-2 (VC) - C100-109 (VCTA)
|
Always
|
Below 1 Ω
|
C27-3 (VTA2) or C100-87 (VTA2) - Body ground
|
Always
|
10 kΩ or higher
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
|