| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM100000001DU9W |
| Model Year Start: 2019 | Model: Camry | Prod Date Range: [08/2018 - 03/2020] |
| Title: METER / GAUGE / DISPLAY: METER / GAUGE SYSTEM: B150013; Fuel Sender Circuit Open; 2019 - 2020 MY Camry [08/2018 - 03/2020] | ||
|
DTC |
B150013 |
Fuel Sender Circuit Open |
DESCRIPTION
This DTC is stored when the combination meter assembly detects a fuel sender gauge assembly malfunction via a direct line.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
Memory |
Note |
|---|---|---|---|---|---|
|
B150013 |
Fuel Sender Circuit Open |
Diagnosis Condition:
Malfunction Status:
|
|
DTC stored |
- |
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
PROCEDURE
|
1. |
READ VALUE USING TECHSTREAM (FUEL INPUT) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Combination Meter / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Combination Meter > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Fuel Input |
Fuel input |
Min.: 0 L, Max.: 655.34 L |
Fuel Tank 60 L:
Fuel Tank 55 L:
|
- |
Body Electrical > Combination Meter > Data List
|
Tester Display |
|---|
|
Fuel Input |
|
Result |
Proceed to |
|---|---|
|
Fuel level data can be displayed on the Techstream |
A |
|
Fuel level data cannot be displayed on the Techstream |
B |
| A |
|
|
|
2. |
CHECK HARNESS AND CONNECTOR (FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY - COMBINATION METER ASSEMBLY) |
(a) Disconnect the R44 fuel suction tube with pump and gauge assembly connector.
(b) Disconnect the K21 combination meter assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
R44-1 (FV) - K21-15 (FV) |
Always |
Below 1 Ω |
|
R44-3 (FS) - K21-14 (FR) |
Always |
Below 1 Ω |
|
R44-2 (FE) - K21-33 (FE) |
Always |
Below 1 Ω |
|
R44-1 (FV) or K21-15 (FV) - Body ground |
Always |
10 kΩ or higher |
|
R44-3 (FS) or K21-14 (FR) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
3. |
INSPECT FUEL SENDER GAUGE ASSEMBLY |
(a) Remove the fuel sender gauge assembly.
for A25A-FKS: Click here
![2018 - 2020 MY Camry [06/2017 - 10/2020]; A25A-FKS (FUEL): FUEL SENDER GAUGE ASSEMBLY: REMOVAL](/t3Portal/stylegraphics/info.gif)
for 2GR-FKS: Click here
(b) Inspect the fuel sender gauge assembly.
for A25A-FKS: Click here
for 2GR-FKS: Click here
| NG |
|
REPLACE FUEL SENDER GAUGE ASSEMBLY for A25A-FKS: Click here
for 2GR-FKS: Click here
|
|
|
4. |
INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY |
|
*a |
Component without harness connected (Fuel Suction Tube with Pump and Gauge Assembly) |
(a) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
R44-1 (FV) - A-3 |
Always |
Below 1 Ω |
|
R44-2 (FE) - A-2 |
Always |
Below 1 Ω |
|
R44-3 (FS) - A-1 |
Always |
Below 1 Ω |
|
R44-1 (FV) - R44-3 (FS) or A-3 - A-1 |
Always |
10 kΩ or higher |
|
R44-1(FV) - R44-2(FE) or A-3 - A-2 |
Always |
10 kΩ or higher |
|
R44-2(FE) - R44-3(FS) or A-2 - A-1 |
Always |
10 kΩ or higher |
| OK |
|
| NG |
|
REPLACE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY for A25A-FKS: Click here
for 2GR-FKS: Click here
|
|
|