Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM1000000016BO4
Model Year Start: 2018 Model: Camry Prod Date Range: [03/2017 -           ]
Title: PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM: U0233; Lost Communication with Blind Spot Monitor Master Module; 2018 - 2024 MY Camry [03/2017 -        ]

DTC

U0233

Lost Communication with Blind Spot Monitor Master Module

DESCRIPTION

This DTC is stored when the blind spot monitor sensor LH judges that there is a communication problem with the blind spot monitor sensor RH.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

U0233

Lost Communication with Blind Spot Monitor Master Module

The blind spot monitor sensor (slave) cannot receive signals from the blind spot monitor sensor (master)

  • Blind spot monitor sensor RH
  • Blind spot monitor sensor LH
  • Wire harness or connector

CAUTION / NOTICE / HINT

NOTICE:

When checking for DTCs, make sure that the blind spot monitor system is turned on.

HINT:

  • Operating the engine switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
  • Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

PROCEDURE

1.

CHECK DTC OUTPUT

(a) Turn the engine switch off.

(b) Turn the engine switch on (IG).

(c) Clear the DTCs.

Body Electrical > Blind Spot Monitor Slave > Clear DTCs

(d) Check for DTCs.

Body Electrical > Blind Spot Monitor Slave > Trouble Codes

Result

Proceed to

DTC U0233 is output

A

No DTCs are output

B

B

USE SIMULATION METHOD TO CHECK 2018 MY Camry [03/2017 - 06/2017]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2018 MY Camry [06/2017 - 08/2018]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2019 MY Camry [08/2018 - 09/2019]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2020 MY Camry [09/2019 - 03/2020]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2020 MY Camry [03/2020 - 10/2020]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2021 MY Camry [10/2020 - 08/2021]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2022 - 2024 MY Camry [08/2021 -        ]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING

A

2.

REPLACE BLIND SPOT MONITOR SENSOR RH

Click here 2018 MY Camry [03/2017 - 06/2017]; PARK ASSIST / MONITORING: BLIND SPOT MONITOR SENSOR: REMOVAL 2018 - 2020 MY Camry [06/2017 - 10/2020]; PARK ASSIST / MONITORING: BLIND SPOT MONITOR SENSOR: REMOVAL 2021 - 2024 MY Camry [10/2020 -        ]; PARK ASSIST / MONITORING: BLIND SPOT MONITOR SENSOR: REMOVAL

NEXT

3.

CHECK DTC OUTPUT

(a) Check for DTCs.

Body Electrical > Blind Spot Monitor Slave > Trouble Codes

Result

Proceed to

DTC U0233 is output

A

No DTCs are output

B

A

REPLACE BLIND SPOT MONITOR SENSOR LH 2018 MY Camry [03/2017 - 06/2017]; PARK ASSIST / MONITORING: BLIND SPOT MONITOR SENSOR: REMOVAL 2018 - 2020 MY Camry [06/2017 - 10/2020]; PARK ASSIST / MONITORING: BLIND SPOT MONITOR SENSOR: REMOVAL 2021 - 2024 MY Camry [10/2020 -        ]; PARK ASSIST / MONITORING: BLIND SPOT MONITOR SENSOR: REMOVAL

B

END (BLIND SPOT MONITOR SENSOR RH WAS DEFECTIVE)