Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM10000000162SW
Model Year Start: 2018 Model: Camry Prod Date Range: [06/2017 - 10/2020]
Title: SEAT: REAR SEAT RECLINING CONTROL CABLE: REMOVAL; 2018 - 2020 MY Camry [06/2017 - 10/2020]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear seatback lock assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

*: When performing learning using the Techstream.

Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; PARK ASSIST / MONITORING: INTELLIGENT CLEARANCE SONAR SYSTEM: CALIBRATION

Disconnect cable from negative battery terminal

Perform steering sensor zero point calibration

Lane departure alert system (w/ Steering Control)

2018 - 2020 MY Camry [03/2017 - 10/2020]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Pre-collision system

Intelligent clearance sonar system*

Memorize steering angle neutral point

Parking assist monitor system

2018 - 2024 MY Camry [03/2017 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION

Panoramic view monitor system

2018 - 2020 MY Camry [06/2017 - 10/2020]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: INITIALIZATION

CAUTION:

  • Wear protective gloves. Sharp areas on the parts may injure your hands.
  • Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

    Click here 2018 - 2019 MY Camry [06/2017 - 09/2019]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: PRECAUTION 2020 MY Camry [09/2019 - 03/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: PRECAUTION 2020 MY Camry [03/2020 - 10/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: PRECAUTION

PROCEDURE

1. REMOVE SPARE WHEEL COVER ASSEMBLY

Click here 2018 - 2024 MY Camry [03/2017 -        ]; DOOR / HATCH: LUGGAGE COMPARTMENT DOOR SUPPORT: REMOVAL+

2. REMOVE REAR SEAT ASSEMBLY

Click here 2018 - 2019 MY Camry [06/2017 - 09/2019]; SEAT: REAR SEAT ASSEMBLY (for Fold Down Seat Type): REMOVAL 2020 MY Camry [09/2019 - 10/2020]; SEAT: REAR SEAT ASSEMBLY (for Fold Down Seat Type): REMOVAL

3. REMOVE CENTER STOP LIGHT SET

Click here 2018 - 2024 MY Camry [03/2017 -        ]; LIGHTING (EXT): HIGH MOUNTED STOP LIGHT ASSEMBLY: REMOVAL

4. REMOVE LUGGAGE COMPARTMENT TRIM INNER PAD

(a) Remove the luggage compartment trim inner pad.

5. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY LH

Click here 2018 - 2019 MY Camry [06/2017 - 09/2019]; SEAT BELT: REAR SEAT OUTER BELT ASSEMBLY: REMOVAL+ 2020 MY Camry [09/2019 - 10/2020]; SEAT BELT: REAR SEAT OUTER BELT ASSEMBLY: REMOVAL+

6. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

7. REMOVE INNER ROOF SIDE GARNISH LH

Click here 2018 MY Camry [06/2017 - 08/2018]; INTERIOR PANELS / TRIM: ROOF HEADLINING: REMOVAL+ 2019 MY Camry [08/2018 - 09/2019]; INTERIOR PANELS / TRIM: ROOF HEADLINING: REMOVAL+ 2020 MY Camry [09/2019 - 03/2020]; INTERIOR PANELS / TRIM: ROOF HEADLINING: REMOVAL+ 2020 MY Camry [03/2020 - 10/2020]; INTERIOR PANELS / TRIM: ROOF HEADLINING: REMOVAL+

8. REMOVE INNER ROOF SIDE GARNISH RH

HINT:

Use the same procedure as for the LH side.

9. REMOVE REAR SEAT SHOULDER BELT HOLE COVER

Click here 2018 - 2019 MY Camry [06/2017 - 09/2019]; SEAT BELT: REAR SEAT OUTER BELT ASSEMBLY: REMOVAL+ 2020 MY Camry [09/2019 - 10/2020]; SEAT BELT: REAR SEAT OUTER BELT ASSEMBLY: REMOVAL+

10. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY

(a) Remove the 2 clips.

(b) Disengage the 3 clips and 5 guides.

(c) Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly then remove the package tray trim panel assembly.

11. REMOVE ROOM PARTITION BOARD LH

(a) Remove the clip.

(b) Disengage the 2 claws.

(c) Disengage the 4 clips to remove the room partition board LH.

12. REMOVE ROOM PARTITION BOARD RH

(a) Remove the 2 clips.

(b) Disengage the 5 clips to remove the room partition board RH.

13. REMOVE REAR SEATBACK LOCK ASSEMBLY LH

(a) Release the stopper and disengage the guige as shown in the illustration.

*a

Stopper

Release

Remove in this Direction (1)

Remove in this Direction (2)

(b) Remove the 2 nuts and rear seatback lock assembly LH.

14. REMOVE REAR SEATBACK LOCK ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.