Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM1000000015W8W
Model Year Start: 2018 Model: Camry Prod Date Range: [06/2017 - 03/2020]
Title: STEERING COLUMN: STEERING WHEEL: REMOVAL; 2018 - 2020 MY Camry [06/2017 - 03/2020]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during steering wheel assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Disconnect cable from negative battery terminal

Perform steering sensor zero point calibration

Lane Departure Alert System (w/ Steering Control)

2018 - 2020 MY Camry [03/2017 - 10/2020]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Pre-collision system

Intelligent clearance sonar system*

Memorize steering angle neutral point

Parking Assist Monitor System

2018 - 2024 MY Camry [03/2017 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION

Panoramic view monitor system

2018 - 2020 MY Camry [06/2017 - 10/2020]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: INITIALIZATION

*: When performing learning using the Techstream.

Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; PARK ASSIST / MONITORING: INTELLIGENT CLEARANCE SONAR SYSTEM: CALIBRATION

NOTICE:

  • Do not remove/install the spiral cable with sensor sub-assembly with the battery connected and the ignition switch ON.
  • Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the battery connected and the ignition switch ON.
  • Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.

PROCEDURE

1. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

2. REMOVE HORN BUTTON ASSEMBLY

Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: STEERING PAD: REMOVAL

3. REMOVE STEERING WHEEL ASSEMBLY

(a) Disconnect each connector from the spiral cable with sensor sub-assembly.

(b) Using a 10 mm hexagon socket wrench, remove the steering wheel assembly set bolt.

(c) Put matchmarks on the steering wheel assembly and steering main shaft.

*a

Matchmark

(d) Temporarily install the steering wheel assembly set bolt.

NOTICE:

Do not overtighten the steering wheel assembly set bolt.

(e) Using SST, separate the steering wheel assembly.

SST: 09950-50013

09951-05010

09952-05010

09953-05020

09954-05031

09957-04010

SST: 09950-60010

09951-00330

NOTICE:

Apply a small amount of grease to the threads and tip of SST (09953-05020) before use.

*a

Turn

*b

Hold

(f) Remove the steering wheel assembly set bolt and steering wheel assembly.

4. REMOVE STEERING PAD SWITCH ASSEMBLY

Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; STEERING COLUMN: STEERING PAD SWITCH: REMOVAL+

5. REMOVE SHIFT PADDLE SWITCH (TRANSMISSION SHIFT SWITCH ASSEMBLY) (w/ Shift Paddle Switch)

for A25A-FKS: Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE): SHIFT PADDLE SWITCH: REMOVAL+

for 2GR-FKS: Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE): SHIFT PADDLE SWITCH: REMOVAL+

6. REMOVE NO. 1 SWITCH WIRE (w/ Shift Paddle Switch)

for A25A-FKS: Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE): SHIFT PADDLE SWITCH: REMOVAL+

for 2GR-FKS: Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE): SHIFT PADDLE SWITCH: REMOVAL+