INSTALLATION

PROCEDURE

1. INSTALL NO. 1 PARKING BRAKE CABLE ASSEMBLY

(a) Install the No. 1 parking brake cable assembly with the 3 bolts and nut. Torque: Bolt: : 15.5 N·m {158 kgf·cm, 11 ft·lbf} Nut: : 6.0 N·m {61 kgf·cm, 53 in·lbf}

(b) Install the nut. Torque: 6.0 N·m {61 kgf·cm, 53 in·lbf}

(c) Connect the brake pedal support base to the vehicle body with the 2 nuts. Torque: 12.7 N·m {130 kgf·cm, 9 ft·lbf}

(d) Engage the 4 clamps.

2. INSTALL BRAKE PEDAL SUPPORT ASSEMBLY

Click here

3. CONNECT NO. 1 PARKING BRAKE CABLE ASSEMBLY

(a) for Type A:

(1) Connect the No. 1 parking brake cable assembly to the No. 1 parking brake pull rod sub-assembly as shown in the illustration. Torque: 5.4 N·m {55 kgf·cm, 48 in·lbf}

*a Turn *b Hold

(b) for Type B:

(1) Connect the No. 1 parking brake cable assembly to the parking brake equalizer as shown in the illustration.

*1 No. 1 Parking Brake Cable Assembly *2 Parking Brake Equalizer *a Rubber Boot

(2) Slide the rubber boot back as shown in the illustration.

NOTICE:

Securely fit the protrusion on the rubber boot into the No. 1 parking brake cable assembly groove.

4. INSTALL NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (w/ Smart Key System)

Click here

5. INSTALL NO. 1 CONSOLE BOX DUCT (for Dual Type)

(a) Install the No. 1 console box duct with the clip as shown in the illustration.

Install in this Direction

6. INSTALL REAR NO. 1 AIR DUCT

Click here

7. INSTALL REAR NO. 2 AIR DUCT

(a) Engage the 4 claws to install the rear No. 2 air duct as shown in the illustration.

Install in this Direction

8. INSTALL FRONT FLOOR CARPET ASSEMBLY

(a) for LH Side:

(1) Install the front floor carpet assembly to its original position as shown in the illustration.

Fastener

-

-

(2) Engage each fastener and the 3 guides to connect the front floor carpet assembly.

(3) Install the 2 front floor carpet clips.

(b) for RH Side:

(1) Install the front floor carpet assembly to its original position as shown in the illustration.

(2) Engage the 3 guides to connect the front floor carpet assembly.

(3) Install the 2 front floor carpet clips.

9. INSTALL FRONT FLOOR CAUTION PLATE COVER (for TMC Made)

Click here

10. INSTALL ACCELERATOR PEDAL

Click here

11. INSTALL LOWER CENTER PILLAR GARNISH LH

Click here

12. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

Click here

13. INSTALL REAR DOOR SCUFF PLATE LH

Click here

14. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Click here

15. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Click here

16. INSTALL LOWER CENTER PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.

17. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.

18. INSTALL REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

19. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.

20. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

21. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

22. INSTALL REAR SEAT CUSHION LOCK HOOK

for Fold Down Seat Type: Click here

for Fixed Seat Type: Click here

23. INSTALL REAR SEAT CUSHION ASSEMBLY

for TMC Made Fold Down Seat Type: Click here

for TMMK Made Fold Down Seat Type: Click here

for TMMK Made Fixed Seat Type: Click here

24. CONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY (for Fold Down Seat Type)

for TMC Made: Click here

25. INSTALL CONSOLE BOX ASSEMBLY

Click here

26. INSTALL FRONT SEAT ASSEMBLY LH

for TMC Made Power Seat: Click here

for TMMK Made Power Seat: Click here

for TMMK Made Manual Seat: Click here

27. INSTALL FRONT SEAT ASSEMBLY RH

for TMC Made Manual Seat: Click here

for TMMK Made Power Seat: Click here

for TMMK Made Manual Seat: Click here

28. INSTALL PARKING BRAKE PEDAL ASSEMBLY

Click here