| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM1000000015PYY |
| Model Year Start: 2018 | Model: Camry | Prod Date Range: [06/2017 - 09/2019] |
| Title: PARK ASSIST / MONITORING: REAR CROSSING TRAFFIC ALERT BUZZER: REMOVAL; 2018 - 2019 MY Camry [06/2017 - 09/2019] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during blind spot monitor buzzer removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced
|
Replaced Part or Performed Procedure |
Necessary Procedures |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
*: When performing learning using the Techstream.
Click here
|
|||
|
Disconnect cable from negative battery terminal |
Perform steering sensor zero point calibration |
Lane departure alert system (w/ Steering Control) |
|
|
Pre-collision system |
|||
|
Intelligent clearance sonar system* |
|||
|
Memorize steering angle neutral point |
Parking assist monitor system |
|
|
|
Panoramic view monitor system |
|
||
CAUTION:
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click here
![2018 - 2019 MY Camry [06/2017 - 09/2019]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: PRECAUTION](/t3Portal/stylegraphics/info.gif)
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here
2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
for A25A-FKS:
Click here
for 2GR-FKS:
Click here
CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
- If an airbag deploys for any reason, it may cause a serious injury.
3. DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY (for TMC Made)
Click here
4. REMOVE REAR SEAT CUSHION ASSEMBLY
for TMC Made:
Click here
for TMMK Made:
Click here
5. REMOVE REAR SEAT CUSHION LOCK HOOK
Click here
6. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH
Click here
7. REMOVE REAR SIDE SEATBACK ASSEMBLY LH
Click here
8. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH
HINT:
Use the same procedure as for the LH side.
9. REMOVE REAR SIDE SEATBACK ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
10. REMOVE INNER ROOF SIDE GARNISH LH
Click here
11. REMOVE INNER ROOF SIDE GARNISH RH
HINT:
Use the same procedure as for the LH side.
12. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY LH
Click here
13. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
14. REMOVE CENTER STOP LIGHT SET
Click here
15. REMOVE REAR SEAT SHOULDER BELT HOLE COVER
Click here
16. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY
Click here
17. REMOVE BLIND SPOT MONITOR BUZZER
|
(a) Disengage the clamp. |
|
(b) Disconnect the connector to remove the blind spot monitor buzzer.
|
|