SUPPLEMENTAL RESTRAINT SYSTEMS: CENTER AIRBAG SENSOR ASSEMBLY: REMOVAL; 2018 - 2019 MY Camry [06/2017

Last Modified: 11-20-2023	6.11:8.1.0	Doc ID: RM1000000015P71
Model Year Start: 2018	Model: Camry	Prod Date Range: [06/2017 - 09/2019]
Title: SUPPLEMENTAL RESTRAINT SYSTEMS: CENTER AIRBAG SENSOR ASSEMBLY: REMOVAL; 2018 - 2019 MY Camry [06/2017 - 09/2019]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during airbag sensor assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed	Link
*: When performing learning using the Techstream. Click here
Replacement of the airbag sensor assembly	Perform system variant learning and acceleration sensor zero point calibration.	VSC disabled or malfunctioning DTCs are output Slip indicator light illuminated ABS warning light illuminated	w/o Electric Parking Brake System: w/ Electric Parking Brake System:
Removal/installation of the front passenger seat	Zero point calibration (Occupant classification system)	Occupant classification system Passenger airbag ON/OFF indicator Airbag system (Front passenger side) Seat belt warning system (Front passenger)
Disconnect cable from negative battery terminal	Perform steering sensor zero point calibration	Lane departure alert system (w/ Steering Control)
		Pre-collision system
		Intelligent clearance sonar system*
	Memorize steering angle neutral point	Parking assist monitor system
	Memorize steering angle neutral point	Panoramic view monitor system

PROCEDURE

1. PRECAUTION

CAUTION:

Be sure to read Precaution thoroughly before servicing.

Click here

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here

2. REMOVE FRONT SEAT ASSEMBLY LH (for TMC Made)

Click here

3. REMOVE FRONT SEAT ASSEMBLY LH (for TMMK Made)

for Manual Seat: Click here

for Power Seat: Click here

4. REMOVE FRONT SEAT ASSEMBLY RH (for TMC Made)

Click here

5. REMOVE FRONT SEAT ASSEMBLY RH (for TMMK Made)

HINT:

Use the same procedure as for the LH side.

for Manual Seat: Click here

for Power Seat: Click here

6. REMOVE CONSOLE BOX ASSEMBLY

Click here

7. DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY (for Fold Down Seat Type)

for TMC Made: Click here

8. REMOVE REAR SEAT CUSHION ASSEMBLY

for TMC Made Fold Down Seat Type: Click here

for TMMK Made Fold Down Seat Type: Click here

for TMMK Made Fixed Seat Type: Click here

9. REMOVE REAR SEAT CUSHION LOCK HOOK

for Fold Down Seat Type: Click here

for Fixed Seat Type: Click here

10. REMOVE FRONT DOOR SCUFF PLATE LH

Click here

11. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

Click here

12. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

HINT:

Disconnect the front door opening trim weatherstrip LH to the extent that allows the removal of the lower center pillar garnish LH.

13. REMOVE REAR DOOR SCUFF PLATE LH

Click here

14. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH

HINT:

Disconnect the rear door opening trim weatherstrip LH to the extent that allows the removal of the lower center pillar garnish LH.

15. REMOVE LOWER CENTER PILLAR GARNISH LH

Click here

16. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Click here

17. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

Click here

18. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

Click here

19. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Disconnect the front door opening trim weatherstrip RH to the extent that allows the removal of the lower center pillar garnish RH.

20. REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

Click here

21. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Disconnect the rear door opening trim weatherstrip RH to the extent that allows the removal of the lower center pillar garnish RH.

22. REMOVE LOWER CENTER PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.

Click here

23. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Click here

24. REMOVE ACCELERATOR PEDAL PAD

for A25A-FKS: Click here

for 2GR-FKS: Click here

25. REMOVE ACCELERATOR PEDAL

for A25A-FKS: Click here

for 2GR-FKS: Click here

26. REMOVE FRONT FLOOR CAUTION PLATE COVER (for TMC Made)

Click here

27. DISCONNECT FRONT FLOOR CARPET ASSEMBLY

Click here

28. REMOVE NO. 1 CONSOLE BOX DUCT (for Dual Type)

Click here

29. REMOVE AIRBAG SENSOR ASSEMBLY

(a) Check that the ignition switch is off.

(b) Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(c) Push down the part (A) in the direction indicated by the arrow (1) to release the lock, and then move the lock lever in the direction indicated by the arrow (2) shown in the illustration to disconnect the connectors.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.

*a	Lock Lever
	Release the lock (1)
	Disconnect the connector (2)

(d) Remove the 3 bolts and airbag sensor assembly.