Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM1000000015P68
Model Year Start: 2018 Model: Camry Prod Date Range: [06/2017 - 10/2020]
Title: SUPPLEMENTAL RESTRAINT SYSTEMS: STEERING PAD: REMOVAL; 2018 - 2020 MY Camry [06/2017 - 10/2020]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during horn button assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

*: When performing learning using the Techstream.

Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; PARK ASSIST / MONITORING: INTELLIGENT CLEARANCE SONAR SYSTEM: CALIBRATION

Disconnect cable from negative battery terminal

Perform steering sensor zero point calibration

Lane departure alert system (w/ Steering Control)

2018 - 2020 MY Camry [03/2017 - 10/2020]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Pre-collision system

Intelligent clearance sonar system*

Memorize steering angle neutral point

Parking assist monitor system

2018 - 2024 MY Camry [03/2017 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION

Panoramic view monitor system

2018 - 2020 MY Camry [06/2017 - 10/2020]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: INITIALIZATION

PROCEDURE

1. PRECAUTION

CAUTION:

Be sure to read Precaution thoroughly before servicing.

Click here 2018 - 2019 MY Camry [06/2017 - 09/2019]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: PRECAUTION 2020 MY Camry [09/2019 - 03/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: PRECAUTION 2020 MY Camry [03/2020 - 10/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here 2018 - 2019 MY Camry [06/2017 - 09/2019]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION 2020 MY Camry [09/2019 - 03/2020]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION 2020 - 2024 MY Camry [03/2020 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

for A25A-FKS: Click here 2018 MY Camry [06/2017 - 08/2018]; MAINTENANCE: A25A-FKS BATTERY: REMOVAL+ 2019 - 2020 MY Camry [08/2018 - 10/2020]; MAINTENANCE: A25A-FKS BATTERY: REMOVAL+

for 2GR-FKS: Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; MAINTENANCE: 2GR-FKS BATTERY: REMOVAL+

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here 2018 MY Camry [06/2017 - 08/2018]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION 2019 MY Camry [08/2018 - 09/2019]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION 2020 MY Camry [09/2019 - 03/2020]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION 2020 MY Camry [03/2020 - 10/2020]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION

3. REMOVE LOWER NO. 2 STEERING WHEEL COVER (w/ Cover)

(a) Using a screwdriver with its tip wrapped with protective tape, disengage each claw to remove the 3 lower No. 2 steering wheel covers.

HINT:

Be careful when disengaging the claws, as the lower No. 2 steering wheel cover may fly off.

*A

for LH Side

*B

for RH Side

*C

for Under Side

-

-

*a

Protective Tape

-

-

4. REMOVE HORN BUTTON ASSEMBLY

CAUTION:

When storing the horn button assembly, keep the airbag deployment side facing upward.

Deployment Side

(a) Check that the ignition switch is off.

(b) Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(c) Using a thin screwdriver, push the 3 torsion springs to disengage the 3 pins as shown in the illustration.

*a

Torsion Spring

Push in this Direction

NOTICE:

Lightly hold the horn button assembly so that it does not fall.

HINT:

Insert the thin screwdriver from the 3 holes of the steering wheel lower cover.

(d) Pull out the horn button assembly from the steering wheel assembly and hold the horn button assembly with one hand.

NOTICE:

When separating the horn button assembly, do not pull the airbag wire harness.

(e) Disconnect the horn connector from the horn button assembly.

*a

Airbag Connector

*b

Horn Connector

*c

Airbag Connector Locking Button

*d

Protective Tape

*e

Wire Harness Clamp

Release in this Direction

Remove in this Direction

(f) Using a screwdriver with its tip wrapped with protective tape, release the 2 airbag connector locking buttons.

(g) Disconnect the 2 airbag connectors.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.

(h) Using a screwdriver with its tip wrapped with protective tape, release the lock and remove the wire harness clamp to remove the horn button assembly.