Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM1000000015P3R
Model Year Start: 2018 Model: Camry Prod Date Range: [06/2017 - 10/2020]
Title: A25A-FKS (BATTERY / CHARGING): GENERATOR: REMOVAL; 2018 - 2020 MY Camry [06/2017 - 10/2020]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the generator assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replacement Part or Procedure

Necessary Procedures

Effects / Inoperative when not performed

Link
*: When performing learning using the Techstream.

Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; PARK ASSIST / MONITORING: INTELLIGENT CLEARANCE SONAR SYSTEM: CALIBRATION

Battery terminal is disconnected/reconnected

Perform steering sensor zero point calibration

Lane departure alert system (w/ Steering Control)

2018 - 2020 MY Camry [03/2017 - 10/2020]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Pre-collision system

Intelligent clearance sonar system*

Memorize steering angle neutral point

Parking assist monitor system

2018 - 2024 MY Camry [03/2017 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION

Panoramic view monitor system

2018 - 2020 MY Camry [06/2017 - 10/2020]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: INITIALIZATION

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click here 2018 - 2019 MY Camry [06/2017 - 09/2019]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION 2020 MY Camry [09/2019 - 03/2020]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION 2020 - 2024 MY Camry [03/2020 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here 2018 - 2019 MY Camry [06/2017 - 09/2019]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION 2020 MY Camry [09/2019 - 03/2020]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION 2020 - 2024 MY Camry [03/2020 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Click here 2018 MY Camry [06/2017 - 08/2018]; MAINTENANCE: A25A-FKS BATTERY: REMOVAL+ 2019 - 2020 MY Camry [08/2018 - 10/2020]; MAINTENANCE: A25A-FKS BATTERY: REMOVAL+

3. REMOVE COOL AIR INTAKE DUCT SEAL

Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; EXTERIOR PANELS / TRIM: FRONT BUMPER: REMOVAL+

4. REMOVE INLET AIR CLEANER ASSEMBLY

Click here 2018 MY Camry [06/2017 - 08/2018]; A25A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+ 2019 MY Camry [08/2018 - 09/2019]; A25A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+ 2020 MY Camry [09/2019 - 03/2020]; A25A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+ 2020 MY Camry [03/2020 - 10/2020]; A25A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

5. REMOVE E.F.I. VACUUM SENSOR ASSEMBLY (MANIFOLD ABSOLUTE PRESSURE SENSOR)

Click here 2018 - 2024 MY Camry [03/2017 -        ]; A25A-FKS (EMISSION CONTROL): VACUUM SENSOR: REMOVAL+

6. REMOVE V-RIBBED BELT

Click here 2018 - 2024 MY Camry [03/2017 -        ]; MAINTENANCE: A25A-FKS DRIVE BELT: REMOVAL

7. REMOVE GENERATOR ASSEMBLY

(a) Disconnect the generator assembly connector.

(b) Open the terminal cap.

(c) Remove the nut and disconnect the wire harness from terminal B.

(d) Remove the bolt and separate the wire harness clamp bracket from the generator assembly.

(e) Remove the 2 nuts and loosen the bolt.

(f) Using an E8 "TORX" socket wrench, remove the 2 stud bolts.

(g) Remove the bolt and generator assembly.