- Replacement of fuel pump assembly
- Replacement of throttle body with motor assembly
- Cleaning the deposits from the throttle body with motor assembly
- Replacement of EGR valve assembly
- Gas leak from exhaust system is repaired
| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM1000000015OW8 |
| Model Year Start: 2018 | Model: Camry | Prod Date Range: [06/2017 - 03/2020] |
| Title: A25A-FKS (FUEL): FUEL PUMP (for High Pressure): REMOVAL; 2018 - 2020 MY Camry [06/2017 - 03/2020] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel pump assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
*: When performing learning using the Techstream.
Click here
|
|||
|
Battery terminal is disconnected/reconnected |
Perform steering sensor zero point calibration |
Lane departure alert system (w/ Steering Control) |
|
|
Pre-collision system |
|||
|
Intelligent clearance sonar system* |
|||
|
Memorize steering angle neutral point |
Parking assist monitor system |
|
|
|
Panoramic view monitor system |
|
||
|
|
Inspection after repair |
|
|
CAUTION:
-
Never perform work on fuel system components near any possible ignition sources.
- Vaporized fuel could ignite, resulting in a serious accident.
-
Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.
- Sparks could cause vaporized fuel to ignite, resulting in a serious accident.
-
To prevent serious injury due to fuel spray from the high-pressure fuel lines, always discharge fuel system pressure before removing any fuel system components.
NOTICE:
This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click here
![2018 - 2019 MY Camry [06/2017 - 09/2019]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION](/t3Portal/stylegraphics/info.gif)
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here
2. DISCHARGE FUEL SYSTEM PRESSURE
Click here
3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here
4. REMOVE INTAKE MANIFOLD
Click here
5. DISCONNECT FUEL TUBE SUB-ASSEMBLY
|
(a) Disconnect the fuel tube sub-assembly from the fuel pump assembly. Click here
|
|
6. REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY
|
(a) Disconnect the ignition coil connector. |
|
(b) for EGR Valve Bracket Connection Type:
|
(1) Using a 17 mm union nut wrench, loosen the 2 union nuts of the No. 1 fuel pipe sub-assembly. |
|
(c) for Cylinder Head Cover Sub-assembly Connection Type:
(1) Using a 17 mm union nut wrench, loosen the 2 union nuts of the No. 1 fuel pipe sub-assembly.
|
Union Nut |
|
Bolt |
(2) Using an 8 mm socket wrench, remove the bolt.
|
(d) Loosen the 2 bolts of the fuel pump assembly. |
|
(e) Remove the No. 1 fuel pipe sub-assembly from the fuel delivery pipe and fuel pump assembly.
7. REMOVE FUEL(ENGINE ROOM SIDE) PUMP ASSEMBLY
NOTICE:
When replacing the fuel pump assembly, it is necessary to replace the No. 1 fuel pipe sub-assembly with a new one.
|
(a) Disconnect the fuel pump assembly connector. |
|
|
(b) Remove the 2 bolts, fuel pump assembly and fuel pump flange from the cylinder head cover sub-assembly. |
|
|
(c) Remove the O-ring from the fuel pump assembly. |
|
|
(d) Remove the fuel pump lifter assembly from the fuel pump lifter guide. |
|
|
(e) Remove the fuel pump spacer gasket from the cylinder head cover sub-assembly. |
|
|
|