| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM1000000015L8B |
| Model Year Start: 2018 | Model: Camry | Prod Date Range: [06/2017 - ] |
| Title: 2GR-FKS (ENGINE CONTROL): SFI SYSTEM: ECM Power Source Circuit; 2018 - 2024 MY Camry [06/2017 - ] | ||
|
ECM Power Source Circuit |
DESCRIPTION
When the engine switch is turned on (IG), the battery voltage is applied to the IGSW terminal of the ECM.
The output signal from the MREL terminal of the ECM causes a current to flow to the coil of the EFI-MAIN NO. 1 relay, closing the contacts and supplying power to terminals +B and +B2 of the ECM.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
PROCEDURE
|
1. |
CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND) |
(a) Disconnect the ECM connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
C96-53 (E1) - Body ground |
Always |
Below 1 Ω |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
2. |
CHECK TERMINAL VOLTAGE (IGSW TERMINAL VOLTAGE) |
|
(a) Disconnect the ECM connector. |
|
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
A21-4 (IGSW) - Body ground |
Engine switch on (IG) |
11 to 14 V |
| NG |
|
|
|
3. |
INSPECT EFI-MAIN NO. 1 RELAY |
(a) Inspect the EFI-MAIN NO. 1 relay.
Click here
![2018 - 2024 MY Camry [06/2017 - ]; 2GR-FKS (ENGINE CONTROL): RELAY: ON-VEHICLE INSPECTION](/t3Portal/stylegraphics/info.gif)
| NG |
|
REPLACE EFI-MAIN NO. 1 RELAY |
|
|
4. |
CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - ECM) |
(a) Disconnect the ECM connector.
(b) Remove the EFI-MAIN NO. 1 relay from the engine room relay block and junction block assembly.
HINT:
Remove the EFI-MAIN NO. 2 and EFI-MAIN NO. 3 relays connected between the checked terminals as the coil inside the relay influences the measurement value.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
2 (EFI-MAIN NO.1 relay) - A21-46 (MREL) |
Always |
Below 1 Ω |
|
5 (EFI-MAIN NO.1 relay) - A21-2 (+B) |
Always |
Below 1 Ω |
|
5 (EFI-MAIN NO.1 relay) - A21-3 (+B2) |
Always |
Below 1 Ω |
|
2 (EFI-MAIN NO.1 relay) or A21-46 (MREL) - Body ground and other terminals |
Always |
10 kΩ or higher |
|
5 (EFI-MAIN NO.1 relay) or A21-2 (+B) - Body ground and other terminals |
Always |
10 kΩ or higher |
|
5 (EFI-MAIN NO.1 relay) or A21-3 (+B2) - Body ground and other terminals |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
5. |
CHECK TERMINAL VOLTAGE (POWER SOURCE OF EFI-MAIN NO. 1 RELAY) |
|
*1 |
Engine Room Relay Block and Junction Block Assembly |
|
*2 |
EFI-MAIN NO. 1 Relay |
(a) Remove the EFI-MAIN NO. 1 relay from the engine room relay block and junction block assembly.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
3 (EFI-MAIN NO. 1 relay) - Body ground |
Always |
11 to 14 V |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - EFI-MAIN NO. 1 RELAY) |
|
|
6. |
CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - BODY GROUND) |
(a) Remove the EFI-MAIN NO. 1 relay from the engine room relay block and junction block assembly.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
1 (EFI-MAIN NO. 1 relay) - Body ground |
Always |
Below 1 Ω |
| OK |
|
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE
|
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
7. |
INSPECT IG2 NO. 1 RELAY |
(a) Inspect the IG2 NO. 1 relay.
Click here
| NG |
|
REPLACE IG2 NO. 1 RELAY |
|
|
8. |
CHECK HARNESS AND CONNECTOR (IG2 NO. 1 RELAY - ECM) |
(a) Disconnect the ECM connector.
(b) Remove the IG2 NO. 1 relay from the engine room relay block and junction block assembly.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
3 (IG2 NO. 1 relay) - A21-4 (IGSW) |
Always |
Below 1 Ω |
|
3 (IG2 NO. 1 relay) or A21-4 (IGSW) - Body ground and other terminals |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
9. |
CHECK TERMINAL VOLTAGE (POWER SOURCE OF IG2 NO. 1 RELAY) |
|
*1 |
Engine Room Relay Block and Junction Block Assembly |
|
*2 |
IG2 NO. 1 Relay |
(a) Remove the IG2 NO. 1 relay from the engine room relay block and junction block assembly.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
5 (IG2 NO. 1 relay) - Body ground |
Always |
11 to 14 V |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IG2 NO. 1 RELAY) |
|
|
10. |
CHECK HARNESS AND CONNECTOR (IG2 NO. 1 RELAY - BODY GROUND) |
(a) Remove the IG2 NO. 1 relay from the engine room relay block and junction block assembly.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
2 (IG2 NO. 1 relay) - Body ground |
Always |
Below 1 Ω |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
11. |
CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - IG2 NO. 1 RELAY) |
(a) Disconnect the certification ECU (smart key ECU assembly) connector.
(b) Remove the IG2 NO. 1 relay from the engine room relay block and junction block assembly.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
K62-17 (IG1D) - 1 (IG2 NO. 1 relay) |
Always |
Below 1 Ω |
|
K62-17 (IG1D) or 1 (IG2 NO. 1 relay) - Body ground and other terminals |
Always |
10 kΩ or higher |
| OK |
|
CHECK SMART KEY SYSTEM
|
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|