Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM1000000015L21
Model Year Start: 2018 Model: Camry Prod Date Range: [06/2017 - 10/2020]
Title: PARK ASSIST / MONITORING: INTELLIGENT CLEARANCE SONAR SYSTEM: C164F; Brake Hydraulic Pressure Malfunction; 2018 - 2020 MY Camry [06/2017 - 10/2020]

DTC

C164F

Brake Hydraulic Pressure Malfunction

DESCRIPTION

When a malfunction signal sent from the skid control ECU via CAN communication is detected by the clearance warning ECU assembly, DTC C164F is stored.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

C164F

Brake Hydraulic Pressure Malfunction

Brake master cylinder brake fluid pressure abnormal

Vehicle stability control system

CAUTION / NOTICE / HINT

NOTICE:

  • After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here 2018 - 2019 MY Camry [06/2017 - 09/2019]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION 2020 MY Camry [09/2019 - 03/2020]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION 2020 - 2024 MY Camry [03/2020 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

  • After replacing an ultrasonic sensor or the clearance warning ECU assembly, perform the necessary procedures (adjustment, calibration, initialization or registration).

    Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; PARK ASSIST / MONITORING: INTELLIGENT CLEARANCE SONAR SYSTEM: CALIBRATION

PROCEDURE

1.

CHECK DTC OUTPUT

(a) Using the Techstream, check for DTCs according to the prompts on the screen.

HINT:

After turning the engine switch from off to on (IG), wait 4 seconds or more before checking for DTCs.

Body Electrical > Advanced Parking Guidance/ICS/Intuitive P/A > Trouble Codes

(b) Clear the DTCs according to the screen on the Techstream.

Body Electrical > Advanced Parking Guidance/ICS/Intuitive P/A > Clear DTCs

(c) Recheck for DTCs.

Body Electrical > Advanced Parking Guidance/ICS/Intuitive P/A > Trouble Codes

HINT:

  • DTC C164F is stored when a malfunction signal sent from the vehicle stability control system is detected.
  • If the malfunctioning part has been repaired or replaced before rechecking for DTCs, DTC C164F will not be output again.
  • If DTC C164F is output frequently, duplicate the conditions that cause the problem symptoms and perform the inspection again, even though the DTC was not output when rechecking for DTCs.

    Click here 2018 MY Camry [06/2017 - 08/2018]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2019 MY Camry [08/2018 - 09/2019]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2020 MY Camry [09/2019 - 03/2020]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2020 MY Camry [03/2020 - 10/2020]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING

Result

Proceed to

DTC C164F is output

A

DTC C164F is not output

B
A

GO TO VEHICLE STABILITY CONTROL SYSTEM

B

USE SIMULATION METHOD TO CHECK 2018 MY Camry [06/2017 - 08/2018]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2019 MY Camry [08/2018 - 09/2019]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2020 MY Camry [09/2019 - 03/2020]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2020 MY Camry [03/2020 - 10/2020]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING