- Engine switch on (IG)
- Intelligent clearance sonar system on
| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM1000000015L1O |
| Model Year Start: 2018 | Model: Camry | Prod Date Range: [06/2017 - 08/2018] |
| Title: PARK ASSIST / MONITORING: INTELLIGENT CLEARANCE SONAR SYSTEM: TERMINALS OF ECU; 2018 MY Camry [06/2017 - 08/2018] | ||
TERMINALS OF ECU
CLEARANCE WARNING ECU ASSEMBLY
(a) Disconnect the R39 clearance warning ECU assembly connector.
(b) Measure the voltage and resistance on the wire harness side connector according to the value(s) in the table below.
|
Terminal No. (Symbol) |
Wiring Color |
Terminal Description |
Condition |
Specified Condition |
|---|---|---|---|---|
|
R39-1 (IG) - R39-30 (E) |
B - B-R |
IG engine source signal |
Engine switch off |
Below 1 V |
|
Engine switch on (IG) |
11 to 14 V |
|||
|
R39-30 (E) - Body ground |
B-R - Body ground |
Ground |
Always |
Below 1 Ω |
(c) Reconnect the R39 clearance warning ECU assembly connector.
(d) Measure the voltage and check for pulses according to the value(s) in the table below.
|
Terminal No. (Symbol) |
Wiring Color |
Terminal Description |
Condition |
Specified Condition |
|---|---|---|---|---|
|
R39-4 (BOF) - R39-30 (E) |
R - B-R |
Power source for front sensor circuit |
Engine switch off |
Below 1 V |
|
|
11 to 14 V |
|||
|
R39-6 (E5) - R39-30 (E) |
W - B-R |
Ground for front clearance sonar |
Always |
Below 1 Ω |
|
R39-8 (SOF) - R39-30 (E) |
L - B-R |
Front sensor communication signal (Front clearance sonar sensor) |
|
Pulse generation (Refer to waveform 1) |
|
R39-14 (CBZ) - R39-13 (EF) |
L-G - L |
Clearance warning buzzer signal |
Buzzer sounding |
Pulse generation (Refer to waveform 2) |
|
R39-22 (BOR) - R39-30 (E) |
B-E - B-R |
Power source for rear sensor circuit |
Engine switch off |
Below 1 V |
|
11 to 14 V |
|||
|
R39-23 (E1) - R39-30 (E) |
G-R - B-R |
Ground for rear clearance sonar |
Always |
Below 1 Ω |
|
R39-24 (SOR) - R39-30 (E) |
S-B - B-R |
Rear sensor communication signal (Rear clearance sonar sensor) |
|
Pulse generation (Refer to waveform 3) |
(e) Using an oscilloscope, check waveform 1.
(1) Waveform 1 (Reference)
|
Item |
Content |
|---|---|
|
Measurement terminal |
R39-8 (SOF) - R39-30 (E) |
|
Measurement setting |
5 V/DIV., 1 ms./DIV. |
|
Condition |
|
(f) Using an oscilloscope, check waveform 2.
(1) Waveform 2 (Reference)
|
Item |
Content |
|---|---|
|
Measurement terminal |
R39-14 (CBZ) - R39-13 (EF) |
|
Measurement setting |
2 V/DIV., 500 μs./DIV. |
|
Condition |
Buzzer sounding |
HINT:
The amplitude of the waveform changes according to the set volume.
(g) Using an oscilloscope, check waveform 3.
(1) Waveform 3 (Reference)
|
Item |
Content |
|---|---|
|
Measurement terminal |
R39-24 (SOR) - R39-30 (E) |
|
Measurement setting |
5 V/DIV., 1 ms./DIV. |
|
Condition |
|
COMBINATION METER ASSEMBLY
Click here
![2018 MY Camry [06/2017 - 08/2018]; METER / GAUGE / DISPLAY: METER / GAUGE SYSTEM: TERMINALS OF ECU](/t3Portal/stylegraphics/info.gif)
ECM
-
for A25A-FKS: Click here
-
for 2GR-FKS: Click here
|
|